Symphonic SF225B - Manual (Page 5)

8. VCR/TV button– Press to select TV or VCR mode.
VCR position: to view playback, to monitor video
recordings or watch TV using the VCR tuner.
TV position: to watch TV or to view one program
while recording another.
9. Remote sensor window– Receives the infrared
signals from the remote control.
10. Indicators
PWR. (power) indicator–
Indicates when the VCR
is turned on.
VCR indicator– Indicates when the VCR is in the
VCR position.
TAPE IN indicator– Indicates when there is a tape
in the VCR.
TIMER indicator– Indicates when the timer record-
ing or OTR has been set.
REC indicator– Indicates during recording. Flashes
when a recording is paused.
CLOCK indicator– Displays current time. PM indi-
cator lits when p.m.
11. TAPE SPEED button– Press to choose the desired
recording speed : SP/SLP.
12. CHANNEL Up or Down buttons– Press to select
the desired channels for viewing or recording.
Tracking function– Press to minimize video ‘noise’
(lines or dots on screen) during playback (only on the
VCR).
Press to stabilize the picture in the Still mode when
the picture begins to vibrate vertically.
13. RECORD button– Press for manual recording.
OTR button– Press to activate One Touch Record-
ing. (only on the VCR)
14. MENU button– Press to display the menu on the TV
screen. Press to exit the menu on the TV screen.
15. NUMBER buttons– Press to select desired channels
for viewing or recording. To select channels from 1
to 9, first press "0" button then 1 to 9. (only on the
remote control)
+100 button– When selecting cable channels which
are higher than 99, press this button first, then press
the last two digits. (To select channel 125, first press
"+100" button then press "2" and "5"). (only on the
remote control)
16. DISPLAY button– Press to display the current time,
channel number, real time tape counter, and other in-
formation on the TV screen. (only on the remote con-
trol)
Each time you press this button, TV screen will
change as shown. The status display (STOP, PLAY
etc.) and the tape speed display (SP, LP (playback
only), or SLP) will disappear after 5 seconds.
17. COUNTER MEMORY button– Press to set counter
memory on and off. (only on the remote control)
18. COUNTER RESET button– Press to reset counter
to 0:00:00. (only on the remote control)
EXIT button– Press to exit the menu on the TV
screen. (only on the remote control)
19. AUTO REPEAT button– Press to repeat playback
automatically. (only on the remote control)
20. Power cord– Connect to a standard AC outlet
(120V/60Hz).
21. AUDIO OUT jack– Connect to the audio input jack
of your audio equipment or another VCR.
22. AUDIO IN jack– Connect to the audio output jack of
your audio equipment or another VCR.
23. ANT. IN terminal– Connect to an antenna, Cable
system or Satellite system.
24. VIDEO OUT jack– Connect to the video input jack
of your video camera or another VCR.
25. VIDEO IN jack– Connect to the video output jack of
your video camera or another VCR.
26. CH3/CH4 selector switch– Use to select a video
output channel (3 or 4) for VCR playback.
27. ANT. OUT terminal– Connects to the antenna input
terminal on your TV.
INSTALLING THE BATTERY
Make sure the polarity of battery to install to the remote
control unit.
STOP
SP 0:12:34
STOP
SP
5:40PM
CH 02
<COUNT mode> <CLOCK mode>
Press
once
<OFF mode>
Press
once
Press once
Install 2 X AA battery
PWR. (power) indicator
Indicador de alimentación
TAPE IN indicator
Indicador de videocasete
introducido
VCR indicator
Indicador de videograbadora
REC (record) indicator
Indicador de grabación (REC)
TIMER indicato
Indicador del temporizador
PM indicator
Indicador del tarde (PM)
CLOCK indicator / Indicador del reloj

INDICATORS

0J11
H7740
- 5 - EN