Sunfire Theater Grand Receiver TGR-401-230 - Manual (Page 28)

User's Manual
8
CHAPTER 3
PUNCH
This mode allows you to set up the
volume, channel up/down and trans-
port buttons so they will work for your
main devices, no matter which device
the remote is set for. For example, the
volume buttons can operate the TV,
even if the remote is set to VCR. The
channel buttons can operate the VCR,
even if the remote is set to TV.
1. In SETUP, select PUNCH and the
display changes to show VOL,
CH, PLAY, MENU, and POWER.
The MENU selection will make the
eight transport buttons around the
navigation pad punch through.
2. Select one of these buttons, for
example VOL.
3. Press a device button for the
device you want the Volume com-
mands to appear in (punch TO).
4. Press a device button for the de-
vice you want to learn from (punch
FROM). These settings are saved.
5. Repeat steps 2 to 4 until you have
punched to all devices you want.
6. Use MAIN to return to SETUP.
NOTE: To erase Punch commands
from a device and so return but-
tons to their previous program-
ming: Repeat steps 1 and 2, then
press the device button twice. Re-
peat for other devices, then press
MAIN to return to SETUP.
The operation of the optional
VIA!migo iPod dock relies on the
navigation buttons when the remote
is set to operate the MP3. Therefore,
it is best that you do not punch-to
the MP3. Also, do not punch-to the
TG401, in case you program over the
navigation buttons used with the OSD
menus and the SIRIUS tuner opera-
tion.
Remote Setup continued
ERASE
Use this mode to erase commands
stored in the remote. This does not
affect the labels, just the stored IR
commands. The pre-programmed
commands for the TGR-401 will not
be lost, as they can be recalled.
1. In the SETUP mode, select
ERASE and the display will show
LEARN, FAV, MACRO and EXIT.
2. If you select LEARN, press ALL
to erase all learned buttons, or
KEY to erase one device at a time,
or DEVIC. If you use KEY, press
MAIN and EXIT when you have
erased all the devices you want.
3. If you select FAV, press ALL to
erase all favorites, or KEY to erase
single favorites. Note that the
labels are not erased.
4. If you select MACRO, press ALL to
erase all macros, or KEY to erase
macros, one device at a time.
5. Press EXIT to return to the SETUP
menu, and press MAIN to return to
the main device menu.
LIGHT
This mode allows you to either dis-
able the light, or change the number
of seconds it stays on. (The light is
inactive while in the SETUP mode).
1. In the SETUP menu, select LIGHT
and the display will show ON, time
in seconds, SAVE and EXIT.
2. If you press ON, it changes to OFF
and disables the light. This is use-
ful if you want to save battery life,
or if the kids like to use the remote
as a flashlight or Light Saber ® .
3. Use the keypad to enter the num-
ber of seconds you want the light
to stay on. If you enter 00, it only
stays on while the light button is
held down.
4. Select SAVE, or press EXIT to
make no change. Either of these
will return you to the SETUP menu.
LEARN
The remote can learn commands
from other remote controls. This is
useful if the pre-programmed com-
mands do not operate some of your
equipment, or certain buttons do not
work, or you want to customize key
functions.
NOTE: PAGE, MAIN, and FAV can-
not be learned over.
1. Find your original remote and
make sure it has good batteries,
and it operates your equipment
perfectly. In the following example,
the Sunfire remote will learn the
PLAY command from a DVD re-
mote.
2. Point the DVD remote into the Red
IR top window of the Sunfire re-
mote. Place them on a flat surface,
about 1 to 2 inches apart, and
avoid bright lighting or sunlight.
3. In the SETUP mode, press
LEARN.
4. Select the DVD device button and
the display will change to show
some common DVD labels (re-
member there are two pages).
5. Select the PLAY button just above
the navigation pad. The display will
show “READY.”
6. Press your DVD remote’s PLAY
button. The display will show
“GOOD” if it has been accepted. If
it shows “FAIL,” press PLAY again.
7. Press another button on the
Sunfire remote and repeat the
procedure until all the DVD buttons
you need are learned.
8. Press MAIN once to return to the
LEARN mode, twice for SETUP
and three times for the MAIN
menu.