Samsung SV-DVD3E EN - Manual (Page 20)

36 37
GB GB
Picture Search, Fast Forward/Rewind
Searching for a Specific Sequence
Picture Search enables you to Fast Forward or Rewind and look for
a particular part of a tape.
1 Press PLAY, the VCR will enter normal play mode. While in play,
press and release the
❿❿ (or ➛➛ ) button. The VCR will search at 5
times the normal playback speed.
2 To return to normal playback mode, press the ❿ II button.
3 If you press and HOLD down the ❿❿ (or ➛➛ ) button the VCR will
search at 9 times the normal speed. Releasing the ❿❿ button will
return the VCR to search at 5 times the normal speed. To return to
normal playback mode, press the
❿ II button.
4 Whilst in Picture Search mode, if you press the ❿❿ button again,
the VCR will enter normal Fast Forward mode.
5 Likewise, whilst in Picture Search ➛➛ mode, if you press the ➛➛
button again, the VCR will enter normal Rewind mode.
6 If, when Redwinding ( ➛➛ ) or Fast Forwarding ( ❿❿ ), you press the
➛➛ (or ❿❿ ) button, the VCR will enter the Picture Search mode.
Each time you record a cassette on this VCR, an “index” is
automatically marked on the tape when recording starts.
The Search function allows you to fast-forward or rewind to a
specific index and start playback from that point. Depending on the
direction selected, the indexes are numbered as follows:
➢
This VCR uses a standard indexing system (VISS). As a
result, it will recognize any indexes marked by other
VCRs using the same system and vice versa.
INTRO SCAN
1 To search for a specific index, press INDEX.
2 Press the ➛➛ or ❿❿ buttons depending on the direction
where your desired programme is located.
3 When an Index mark is found the VCR will playback the tape for 5
seconds, after which it will continue searching for the next Index mark.
4 If you want to watch the tape from a particular Index, simply press ❿ II.
Index Skip Search:
This feature will enable you to fast forward/rewind to a specific
point on a tape: E.g. if you have recorded 3 different programmes
on a tape and you have rewound the tape to the beginning, by
using this feature you can go directly to the start of programme 2
simply by pressing the INDEX button.
1 Press the INDEX to start the Index search.
2 Press the ➛➛ or ❿❿ buttons twice more. This will take
you directly to the start of the desired programme is located.
3 These Index searches can be made forwards: (press ❿❿ ) or
backwards: (press ➛➛ ).
4 To cancel an Index search simply press the ❿ II or ■ button.
➞
2 1 1 2
etc.
Prev
Seq.
Seq. being
played
Next
Seq. etc.
VCR
VCR
Using the Tape Counter
The tape counter:
◆ Indicates the elapsed time in the play and record modes
(hours, minutes and seconds)
◆ Is reset when a cassette is inserted in the DVD-VCR
◆ Allows you to find the beginning of a sequence easily
☛
If the remaining time is to be calculated correctly, you
must indicate the type of cassette being used.
1 Insert a cassette in your DVD-VCR.
2 To set the tape counter to zero at the beginning of a sequence:
◆ Press DISPLAY twice to display the counter
◆ Press CLEAR when you want to set the tape counter to zero
3 When you are ready,
◆ Start playback or Recording.
◆ Press the ■ button.
◆ To fast-forward or rewind to the sequence at which the
counter was set to zero, press
➛➛ or ❿❿ .
➢
Some DVD-VCR information, such as the counter, can be
displayed on the television screen (unless you have
deactivated the OSD mode; refer to page 28).
Press DISPLAY:
◆ Once to display the current function, programme
number, recording speed, date, time and counter
◆ Twice to display the counter only
◆ Three times to display the time remaining on the
cassette
◆ Four times to clear the display
7 8 9
0
3D SOUND SCREEN FIT CLEAR
DVD VCR INPUT SEL.
ZOOM
VIEW
TRK PROG
DISPLAY
F.ADV/STEP
DIGEST
SVHS
ANGLE
A.TRK
2
2
0:00:00
VCR