Sony BLUETOOTH MEX-BT2500 User Manual

Bluetooth ™ audio system, Mex-bt2500

Advertising
background image

© 2007 Sony Corporation

Printed in Thailand

3-100-200-31 (1)

Cautions

Be sure to install this unit in the dashboard of the car
as the rear side of the unit becomes hot during use.

• This unit is designed for negative ground (earth) 12 V

DC operation only.

• Do not get the leads under a screw, or caught in moving

parts (e.g. seat railing).

• Before making connections, turn the car ignition off to

avoid short circuits.

• Connect the yellow and red power supply leads only

after all other leads have been connected.

Run all ground (earth) leads to a common

ground (earth) point.

• Be sure to in su late any loose un con nect ed leads with

electrical tape for safety.

Notes on the power supply lead (yellow)
• When connecting this unit in combination with other

stereo components, the connected car circuit’s rating
must be higher than the sum of each component’s fuse.

• When no car circuits are rated high enough, connect

the unit directly to the battery.

Parts list

• The numbers in the list are keyed to those in the

instructions.

• The bracket

 and the protection collar  are

attached to the unit before shipping. Before mounting
the unit, use the release keys

 to remove the bracket

 and the protection collar  from the unit. For
details, see “Removing the protection collar and the
bracket (

)” on the reverse side of the sheet.

Keep the release keys

for future use as they

are also necessary if you remove the unit from
your car.

Caution
Handle the bracket

 carefully to avoid injuring your

fi ngers.

Note
Before installing, make sure that the catches on both sides of
the bracket

are bent inwards 2 mm (

3

/

32

in). If the catches are

straight or bent outwards, the unit will not be installed securely
and may spring out.

Installation/Connections

Instalación/Conexiones

⫭堩濊丣嵓彂㌉

Bluetooth
Audio System

Connection diagram

To a metal surface of the car

First connect the black ground (earth) lead, then connect the
yellow and red power supply leads.

To the power antenna (aerial) control lead or

power supply lead of antenna (aerial) booster

Notes
It is not necessary to connect this lead if there is no power

antenna (aerial) or antenna (aerial) booster, or with a
manually-operated telescopic antenna (aerial).

When your car has a built-in FM/MW/SW antenna (aerial)

in the rear/side glass, see “Notes on the control and power
supply leads.”

To the + 12 V power terminal which is

energized in the accessory position of the
ignition switch

Notes
If there is no accessory position, connect to the + 12 V

power (battery) terminal which is energized at all times.

Be sure to connect the black ground (earth) lead to a

metal surface of the car fi rst.

When your car has a built-in FM/MW/SW antenna (aerial)

in the rear/side glass, see “Notes on the control and power
supply leads.”

To the + 12 V power terminal which is

energized at all times

Be sure to connect the black ground (earth) lead to a metal
surface of the car fi rst.

Notes on the control and power supply leads
The power antenna (aerial) control lead (blue) supplies + 12 V

DC when you turn on the tuner.

When your car has built-in FM/MW/SW antenna (aerial) in the

rear/side glass, connect the power antenna (aerial) control
lead (blue) or the accessory power supply lead (red) to the
power terminal of the existing antenna (aerial) booster. For
details, consult your dealer.

A power antenna (aerial) without a relay box cannot be used

with this unit.

Memory hold connection
When the yellow power supply lead is connected, power will
always be supplied to the memory circuit even when the ignition
switch is turned off.

Notes on speaker connection
Before connecting the speakers, turn the unit off.
Use speakers with an impedance of 4 to 8 ohms, and with

adequate power handling capacities to avoid its damage.

Do not connect the speaker terminals to the car chassis, or

connect the terminals of the right speakers with those of the
left speaker.

Do not connect the ground (earth) lead of this unit to the

negative (–) terminal of the speaker.

Do not attempt to connect the speakers in parallel.
Connect only passive speakers. Connecting active speakers

(with built-in amplifi ers) to the speaker terminals may damage
the unit.

To avoid a malfunction, do not use the built-in speaker leads

installed in your car if the unit shares a common negative (–)
lead for the right and left speakers.

Do not connect the unit’s speaker leads to each other.

Note on connection
If speaker is not connected correctly, “FAILURE” appears in
the display. In this case, make sure the speaker is connected
correctly.

MEX-BT2500

Precauciones

Asegúrese de instalar la unidad en el tablero del
automóvil, ya que la parte posterior de la unidad se
calienta durante el uso.

• Esta unidad ha sido diseñada para alimentarse sólo con

cc de 12 V de tierra negativa.

• No coloque los cables debajo de ningún tornillo, ni

los aprisione con partes móviles (p. ej. los raíles del
asiento).

• Antes de realizar las conexiones, desactive el

encendido del automóvil para evitar cortocircuitos.

• Conecte los cables de fuente de alimentación amarillo

y rojo solamente después de haber conectado los
demás.

Conecte todos los cables de conexión a masa

a un punto común.

• Por razones de seguridad, asegúrese de aislar con cinta

aislante los cables sueltos que no estén conectados.

Notas sobre el cable de fuente de alimentación
(amarillo)
• Cuando conecte esta unidad en combinación con otros

componentes estéreo, la capacidad nominal del circuito
conectado del automóvil debe ser superior a la suma
del fusible de cada componente.

• Si no hay circuitos del automóvil con capacidad

nominal sufi cientemente alta, conecte la unidad
directamente a la batería.

Lista de componentes

• Los números de la lista corresponden a los de las

instrucciones.

• La unidad se comercializa con el soporte

 y el

marco de protección

. Antes de montarla, utilice las

llaves de liberación

 para extraer el soporte  y

el marco de protección

 de la misma. Para obtener

más información, consulte “Extracción del marco de
protección y del soporte (

)”.

Conserve las llaves de liberación

para

utilizarlas en el futuro, ya que también las
necesitará si retira la unidad del automóvil.

Precaución
Tenga mucho cuidado al manipular el soporte

 para

evitar posibles lesiones en los dedos.

Nota
Antes de instalar la unidad, compruebe que los enganches de
ambos lados del soporte

están doblados hacia adentro 2 mm.

Si no lo están o están doblados hacia afuera, la unidad no se
instalará correctamente y puede saltar.

Diagrama de conexión

A una superfi cie metálica del automóvil

Conecte primero el cable de conexión a masa negro, y
después los cables amarillo y rojo de fuente de alimentación.

Al cable de control de la antena motorizada

o al cable de fuente de alimentación del
amplifi cador de señal de la antena

Notas
Si no se dispone de antena motorizada ni de amplifi cador

de señal de la antena, o se utiliza una antena telescópica
accionada manualmente, no será necesario conectar este
cable.

Si el automóvil incorpora una antena de FM/MW/SW en el

cristal trasero o lateral, consulte “Notas sobre los cables
de control y de fuente de alimentación”.

Al terminal de alimentación de + 12 V que

recibe energía en la posición de accesorio
del interruptor de la llave de encendido

Notas
Si no hay posición de accesorio, conéctelo al terminal de

alimentación (batería) de + 12 V que recibe energía sin
interrupción.

Asegúrese de conectar primero el cable de conexión a

masa negro a una superfi cie metálica del automóvil.

Si el automóvil incorpora una antena de FM/MW/SW en el

cristal trasero o lateral, consulte “Notas sobre los cables
de control y de fuente de alimentación”.

Al terminal de alimentación de + 12 V que

recibe energía sin interrupción

Asegúrese de conectar primero el cable de conexión a masa
negro a una superfi cie metálica del automóvil.

Notas sobre los cables de control y de fuente de
alimentación
El cable de control de la antena motorizada (azul) suministrará

cc de + 12 V cuando conecte la alimentación del sintonizador.

Si el automóvil dispone de una antena de FM/MW/SW

incorporada en el cristal trasero o lateral, conecte el cable
de control de antena motorizada (azul) o el cable de fuente
de alimentación auxiliar (rojo) al terminal de alimentación del
amplifi cador de señal de la antena existente. Para obtener más
información, consulte a su distribuidor.

Con esta unidad no es posible utilizar una antena motorizada

sin caja de relé.

Conexión para protección de la memoria
Si conecta el cable de fuente de alimentación amarillo, el circuito
de la memoria recibirá siempre alimentación, aunque apague el
interruptor de encendido.

Notas sobre la conexión de los altavoces
Antes de conectar los altavoces, desconecte la alimentación

de la unidad.

Utilice altavoces con una impedancia de 4 a 8

con la

capacidad de potencia adecuada para evitar que se dañen.

No conecte los terminales de altavoz al chasis del automóvil,

ni conecte los terminales del altavoz derecho con los del
izquierdo.

No conecte el cable de conexión a masa de esta unidad al

terminal negativo (–) del altavoz.

No intente conectar los altavoces en paralelo.
Conecte solamente altavoces pasivos. Si conecta altavoces

activos (con amplifi cadores incorporados) a los terminales de
altavoz, puede dañar la unidad.

Para evitar fallos de funcionamiento, no utilice los cables de

altavoz incorporados instalados en el automóvil si su unidad
comparte un cable negativo común (–) para los altavoces
derecho e izquierdo.

No conecte los cables de altavoz de la unidad entre sí.

Nota sobre la conexión
Si el altavoz no está conectado correctamente, aparecerá
“FAILURE” en la pantalla. Si es así, compruebe la conexión del
altavoz.

Enganche

Equipment used in illustrations (not supplied)
Equipo utilizado en las ilustraciones (no suministrado)
㌶♢ᶑ䗨堩仒濃曂斨彥濄

Fuse (10 A)
Fusible (10 A)
ὁ旍ᶁ!)21!B*

from car antenna (aerial)
desde la antena del automóvil
㛉兎㯡廊⢍丣

Left
Izquierdo

Right
Derecho

Left
Izquierdo

Right
Derecho

ANT REM

Red
Rojo
丆凖

Yellow
Amarillo
渨凖

Black
Negro
渵凖

Blue
Azul
呁凖

Max. supply current 0.1 A

Corriente máx. de alimentación de 0,1 A

㙤⢋䒙㲥 1/2!B

Rear speaker
Altavoz posterior
⍲㇐⡔◌

Front speaker
Altavoz frontal
↱㇐⡔◌

Catch

Ч 2

Ч 4

㱌び

䒕ᷲ⚌ợ䒌弫䥯ᶑ㚐㚞䗨倰曆Ṿ⌼䁑濇孛∅⼩⭪
㚐㚞⫭堩⚌㯡廊䗨Ṏ埌㛣ᶑɁ

!㚐㚞⍎偡ợ䒌岃㛥㌉⚔䗨!23!W!䙘㲥䒙㷴Ɂ

!≣ợ⭠丣⢝⚌圞ᶁᵯ濇ㅺ亄⚌䥟∌恌Ṛᵮ濃⣦⸋㡩

㇚ㆯ濄Ɂ

!彂㌉丣嵓ᶯ↱濇孛⃗救㯡廊⹹㐲濇ṉ忣₱䝑嵓Ɂ

!⍎㙭彂㌉ᷪㆤ㙭⃚Ḻ⭠丣ᶯ⍲濇⃱彂㌉渨凖⏰丆凖

䒙㷴⭠丣Ɂ

!⭪ㆤ㙭⚔丣恡彂㌉↔⍰ᵤ㌉⚔䀝Ɂ

!ᶞᷪ⫭⃌濇孛∅⼩䒌乁乼做ⶊợㆤ㙭㛢㓇㚎彂㌉䗨

⭠丣乁乼Ɂ

⃗ᷲ䒙㷴⭠丣濃渨凖濄䗨㱌びᷯ柝

!⭪㚐㚞ᵲ⃚⫧䨯ặ⡔堩仒丨⍬ợ䒌㕚濇ㆤ彂㌉䗨㯡

廊䒙嵓⬝愳⼩柟⢋ᷲ⍨堩仒ὁ旍ᶁ⬝愳䗨⾟⏰Ɂ

!⺷㯡廊䒙嵓⬝愳ᵱ⢃⢋㕚濇孛⭪㚐㚞䙘㌉ᵲ吨䒙㯄

䙜彂㌉Ɂ

晚Ṛᵤ夬埌!

!埌ᶑ㓔⪻ᵲ存㕲᷊ᶑ䗨㓔⪻㖓ᵤ兘䗨Ɂ

!堩⋜㒓㜚!

!⏰ὁ㈈䌓!!㖓弴廷ᶯ↱堩⚌㚐堩

仒ᵮ䗨Ɂ⫭堩㚐堩仒ᶯ↱濇ợ䒌⹤摥搉≽!

!Ḳ

㚐堩仒ᵮ⌺ᵯ堩⋜㒓㜚!

!⏰ὁ㈈䌓!!Ɂ孊个

⃩⬝濇孛⌦敩㚐柙⌱曆䗨ĥ㈪⋜ὁ㈈䌓⏰堩⋜㒓㜚!
)

*ĦɁ

!ὁ⪼⣡⹤摥搉≽!

!ṉ⡫⍲䒌Ɂ「Ḳ㯡廊ᵮ⌺ᵯ㚐

堩仒㕚濇㙭⼩壥䒌↔孉搉≽Ɂ

㱌び
⭳⼧ợ䒌堩⋜㒓㜚!!ṉ₱Ẉ↔ㆯ㉫Ɂ


⫭堩↱濇孛䟒嬈堩⋜㒓㜚!!ᶈ弝䗨♞⫾䆫⍵⃩⺓㙖!3!nnɁ⣦㜀♞
⫾䆫䩸䙘ㅺ⍵⡺⺓㙖濇㚐堩仒⭪ᵱ偡䇆♞⫭堩ⷚ⍓偡⺝⅞Ɂ

♞⫾䆫

丣嵓彂㌉♢!

!兗㯡廊愵⯂埌曆

棺€彂㌉渵凖⚔丣濇䂚⍲彂㌉渨凖⏰丆凖䒙㷴⭠丣Ɂ

!兗䒙∌⢍丣㌋↚⭠丣ㅺ⢍丣⊫亍◌䗨䒙㷴⭠丣


!⣦㜀㰅㙭䒙∌⢍丣ㅺ⢍丣⊫亍◌濇ㅺ㙭ㆯ∌ẜ亍⹳⢍丣濇ⅽ

㕄晤彂㌉㫈⭠丣Ɂ

!剉㯡廊䗨⍲0Ἃ䌟䏧⃩㙭⃩仒! GN0NX0TX! ⢍丣濇孛⌦敩ĥ⃗

ᷲ㌋↚⭠丣⏰䒙㷴⭠丣䗨㱌びᷯ柝ĦɁ

!兗!,!23!W!䒙㷴䩓⪴濇孉䩓⪴⚌䀝㿏⹤⃗斨Ṛằ

仒彾䒙


!⣦㜀㰅㙭斨Ṛằ仒濇ⅽ彂㌉兗!,!23!W!䒙㷴濃吨䒙㯄濄䩓⪴濇

孉䩓⪴旳㕚⡨ᷲ彾䒙䈚⽥Ɂ

! 䟒ὁ棺€⭪渵凖⚔丣彂㌉兗㯡廊愵⯂埌曆Ɂ

!剉㯡廊䗨⍲0Ἃ䌟䏧⃩㙭⃩仒! GN0NX0TX! ⢍丣濇孛⌦敩ĥ⃗

ᷲ㌋↚⭠丣⏰䒙㷴⭠丣䗨㱌びᷯ柝ĦɁ

!兗!,!23!W!䒙㷴䩓⪴濇孉䩓⪴旳㕚⡨ᷲ彾䒙䈚⽥

䟒ὁ棺€⭪渵凖⚔丣彂㌉兗㯡廊愵⯂埌曆Ɂ

⃗ᷲ㌋↚⭠丣⏰䒙㷴⭠丣䗨㱌びᷯ柝

!㌉彾孧孴◌䒙㷴㕚濇䒙∌⢍丣䗨㌋↚⭠丣濃呁凖濄ἣ偡㌴ỿ!,!23!W!

䙘㲥䒙Ɂ

!⺷㯡廊䗨⍲0Ἃ䌟䏧䧻ᵮ㙭⃩仒!GN0NX0TX!⢍丣㕚濇孛⭪䒙∌⢍丣

㌋↚丣濃呁凖濄ㅺ廩∍䒙㷴⭠丣濃丆凖濄彂㌉兗䌔㙭⢍丣⊫亍◌
ᵮ䗨䒙㷴䩓⪴ᵮɁ孊个存㕲濇孛ᵲ「䗨丳摤⒪侸䱟Ɂ

!㚐㚞ᵱ偡ợ䒌ᵱ⃛⡫之䒙◌䘶䗨䒙∌⢍丣Ɂ

ὁ㉥嬔⼪䗨丣嵓彂㌉㰹
⺷彂㌉ᷪ渨凖䗨䒙㷴⭠丣㕚濇⋗ợ䀝㿏⹤⃗⃗救濇䒙㷴ḱ⭪⭝嬔
⼪䒙嵓ỿ䒙Ɂ

⃗ᷲ㇐⡔◌彂㌉䗨㱌びᷯ柝

!彂㌉㇐⡔◌ᶯ↱濇孛⃗救㚐㚞䒙㷴Ɂ

!孛ợ䒌斟ㇻᶞ! 5.9! 㪋⤪ᵸ⃛㙭崗⢃∃䋫⡨䍪偡⇿䗨㇐⡔◌濇ṉ

₱㋃⚳Ɂ

!≣⭪㇐⡔◌䩓⪴彂㌉↔㯡廊ⷹ䘼ᵮ濇ㅺ⭪⍗㇐⡔◌䗨䩓⪴ᵲⵊ㇐

⡔◌䗨䩓⪴彂㌉Ɂ

!≣⭪㚐㚞䗨⚔丣彂㌉↔㇐⡔◌䗨岃㛥濃.濄䩓⪴ᵮɁ

!㇐⡔◌ᵱ⍓ⷚ侸彂㌉Ɂ

!孛ḩ彂㌉㕄㷴㇐⡔◌Ɂ⭪㙭㷴㇐⡔◌濃⃛㙭⃩仒㒢⢋◌濄彂㌉↔

㇐⡔◌䩓⪴⍓偡Ṿ㋃⚳㚐㚞Ɂ

!剉㚐㚞ợ䒌ⵊɀ⍗㇐⡔◌䗨⃕䒌岃㛥濃.濄⭠丣濇ᶞᷪ忣₱㒩昀濇

Ⅻ≣ợ䒌⫭堩⚌㯡廊⃩䗨⃩仒㇐⡔◌⭠丣Ɂ

!孛≣⭪㚐㚞㇐⡔◌⭠丣䙜᷶彂㌉Ɂ

彂㌉䗨㱌びᷯ柝
⣦㜀㚎㫇䟒彂㌉㇐⡔◌濇ⅽ㖢䢞⮳ᵮṾ⅞䌔ĥGBJMVSFĦɁ弽㕚濇
孛䟒ὁ㇐⡔◌彂㌉㫇䟒Ɂ

Connection example
Ejemplo de conexiones
丣嵓彂㌉♢ữ

White
Blanco
䗡凖

Green
Verde
乣凖

Purple
Morado
䲏凖

White/black striped
Con rayas blancas y negras
䗡凖濊渵凖㛅丝

Gray/black striped
Con rayas grises y negras
㿔凖濊渵凖㛅丝

Green/black striped
Con rayas verdes y negras
乣凖濊渵凖㛅丝

Gray
Gris
㿔凖

Purple/black striped
Con rayas moradas y negras
䲏凖濊渵凖㛅丝

Advertising