Scag Power Equipment STT-31BSG - Manual (Page 49)

36
Ref. Part
No. No.
Description
Ref. Part
No. No.
Description
38 43294 Spindle Housing
39 43312 Spacer, Outside
40 43296 Spacer, Inside
41 481025 Seal, Bottom
42 43297 Spindle Bushing, Bottom
43 481035 Nut, Special 1 - 1/16-18
44 48114-04 Grease Fitting
45 48677 Relief Fitting, Tapered Spindle
46 481050 Spring, Discharge Chute
47 48038 Guide, Roller
48 482001 Cutter Blade, 21.0” 61”
48 482002 Cutter Blade, 24.5" 72”
49 481516 Gearbox Assembly, Deck Drive
50 481558 Belt, Cutter Deck Drive, 61”
50 481980 Belt, Cutter Deck Drive, 72”
51 45944 Roller Shaft
52 48926 Tapered Hub, 1-1/8" Bore
53 48141 Tapered Hub, 1" Bore
54 461174 Idler Arm, Cutter Deck
55 48224 Bearings, Ball
56 48269 Pulley, Idler
57 422713 Base, Idler Pivot
58 48753 Pulley, 6.35 O.D. - 61”
48967 Pulley, 6.95 O.D. - 72”
59 422426 Mounting Plate, Gearbox
60 422413 Belt Cover, LH - 61”
422677 Belt Cover, LH - 72”
422413 Belt Cover, RH - 61”
422708 Belt Cover, RH - 72”
61 461036 Pusharm (includes items 44, 62, 63 & 64)
62 43309 Spacer, Spindle
63 04020-16 Nut, Hex Head 5/8-18 UNF
64 48763 Rod End, 5/8" Male RH Thread
65 04001-79 Bolt, Hex Head 5/8-11 x 4-1/2"
66 481597 Spring, Cutter Deck
67 48753 Pulley, 6.35 O.D. - 61”
48924 Pulley, 5.75 O.D. - 72”
68 04110-03 U-Nut, 3/8-16
69 04021-13 Nut, Hex Elastic Stop 5/8-11
70 422601 Discharge Baffle 61”
422602 Discharge Baffle 72”
1 461267 Cutter Deck, 61” (Includes Decals)
1 461268 Cutter Deck, 61” Advantage (Includes Decals)
1 461144 Cutter Deck, 72” (Includes Decals)
1 461148 Cutter Deck, 72” Advantage (Includes Decals)
2 04003-04 Bolt, Carriage 5/16-18 x 1"
3 04019-04 Nut, Hex Serrated Flange 3/8-16
4 481625-01 Wing nut, 3/8-16
5 481632 Anti-Scalp Wheel
6 04003-26 Bolt, Carriage 3/8-16 x 4"
7 422478 Anti-Scalp Wheel Bracket
8 04017-27 Bolt, Hex Serrated Flange 3/8-16 x 1"
9 04040-10 Flatwasher, 5/8" (.688 x 1.75 x .134)
10 04021-05 Locknut, 3/8-16 Center Lock
11 461292 Discharge Chute, 61” & 72”
461296 Discharge Chute, 61” & 72” Adv. (Not Shown)
12 04001-12 Bolt, Hex Head 5/16-18 x 1.75" (Front)
04001.11 Bolt, Hex Head 5/16-18 x 1.50” (Rear)
13 04021-10 Nut, Hex Elastic Stop 5/16-18
14 04020-09 Nut, 5/8-11 UNC
15 45332 Push Arm Shaft
16 04001-41 Bolt, Hex Head 5/8-11 x 9.50"
17 04003-12 Bolt, Carriage 5/16-18 x .75"
18 04001-154 Bolt, Hex Head 5/16-18 x 4.75"
19 04063-08 Key, 1/4 x 1/4 x 2"
20 04063-01 Key, 1/4 x 1/4 x 1.25"
21 04043-04 Flatwasher,3/8-.39 x .938 x .105 HD
22 04001-11 Bolt, Hex Head 5/16-18 x 1.50"
22A 04001-12 Bolt, Hex Head 5/16-18 x 1.75”
23 04021-10 Nut, Hex Serrated Flange 5/16-18
24 04001-01 Bolt, Hex Head 1/2-20 x .75"
25 48100-15 Bushing, .376 I.D. Oilite
26 04030-03 Lockwasher, 5/16"
27 04040-15 Flatwasher, 5/16" (.375 x .875 x .083)
28 04041-07 Flatwasher, 3/8" (.391 x .938 x .105)
29 04021-09 Nut, Hex Elastic Stop 3/8-16
30 04001-62 Bolt, Hex Head 3/8-16 x 3.25"
31 04001-31 Bolt, Hex Head 3/8-16 x 2.50"
32 43503 Pivot, Idler - Short
33 04001-136 Bolt, Hex Head 3/8-16 x 1.50" Grade 8
34 46631 Spindle Assembly
35 43298 Spindle Shaft
36 481024 Seal, Top
37 481022 Bearing Assembly
* Common hardware which should be purchased locally. All bolts Grade 5 plated, all other fasteners zinc plated.
61”, 61A, 72", 72”A CUTTER DECKS