Kangol 845S - Manual (Page 3)

3
Service and Repair Manual
Model 845S
FIG. PART NO. DESCRIPTION OF PART NO. REQ.
41 9170 3252 10 Brush Spring (2)
42 9170 4652 10 Speed Control Switch (1)
47 9170 3254 10 Upper Handle Mount (1)
50 9170 4652 30 Motor Cover (1)
51 9170 4656 80 Left Handle Half (1)
52 9170 4657 60 Right Handle Half (1)
53 9170 4658 40 Motor Housing (1)
54 9170 4659 40 Left Shroud (1)
55 9170 4659 50 Right Shroud (1)
56 9170 4659 90 Belly Shroud (1)
59 9170 3251 50 Retaining Ring (1)
62 9170 3250 80 O-Ring (1)
76 9170 3250 70 Retaining Ring (1)
77 9170 3250 50 Torsion Spring (1)
79 9170 3250 30 Compression Spring (2)
80 9170 3251 10 Bearing Cup (1)
82 9170 4660 20 Shift Disk (1)
87 9170 3254 20 Isolation Bellows (1)
88 9170 3253 00 Pivot Isolator (2)
89 9170 3254 30 Isolation Module Assembly (1)
90 9170 3250 20 Rotostop Knob (1)
92 9170 3253 30 Foam Slug Kit (Bag of 10) (1)
93 9170 3252 60 Handle Cushion (1)
110 9170 3254 00 Rubber Washer (2)
114 9170 4660 90 Fan (1)
123 9170 3253 80 Cord Protector (1)
%SEE PAGE 5 FOR
ADDITIONAL LUBRICATION
AND SERVICE NOTES
FIG. PART NO. DESCRIPTION OF PART NO. REQ.
2 9170 4667 30 5 mm Steel Ball (2)
4 9170 3251 20 Ball Bearing (1)
7 9170 3251 60 Ball Bearing (1)
13 9170 3253 10 Pivot Nut (1)
15 9170 3252 90 Pivot Bolt (1)
16 9170 3251 00 M6 x 1.0 x 120 Pan Hd. Slt. Tapt. T-27 (4)
19 9170 3253 90 Special Screw (2)
20 9170 3250 10 8-32 x 3/8" Pan Hd. Slt. Tapt. T-20 (4)
21 9170 3251 90 8-16 x 2" Pan Hd. Slt. Plast. T-20 (2)
24 9170 3252 50 M5 x 2.24 x 18 Pan Hd. Slt. PT T-20 (7)
25 9170 4650 10 Dowel Pin-Knurled (1)
26 9170 4652 70 Round Label (1)
31 9170 4650 60 Electronics Assembly (1)
32 9170 4650 80 120 Volt Armature (1)
33 9170 4651 70 120 Volt Field (1)
34 9170 3237 20 120 V Carbon Brush (2) Kit (1)
36 9170 3252 00 Brush Carrier Assembly (1)
39A 9170 3253 50 Lower Cord Clamp (1)
39B 9170 4665 60 Upper Cord Clamp (1)
40 9170 4651 90 Cord Set (1)
l
EXAMPLE:
Component Parts (Small #) Are Included
When Ordering The Assembly (Large #). 0
00