KORG EASYSTART AX3000G User Manual
Page 3
AX3000G EasyStart
3
2.
Press either the BANK UP or BANK DOWN switch to select “BANK 2”. (When you’re selecting a bank, the bank
number will flash in the BANK display).
3.
Press the PROGRAM SELECT 3 switch. Program “2-3” will be displayed in the LCD instantly. The PROGRAM
SELECT 3 switch LED will light and the Bank Display will indicate 2, and stay lit.
!
If the LED in the upper left of the Bank Up switch is lit green, Individual Mode is selected. Press the BANK UP
switch to choose Program Select mode.
S
S
a
a
v
v
i
i
n
n
g
g
a
a
P
P
r
r
o
o
g
g
r
r
a
a
m
m
You’ve tweaked and turned some knobs, and you like the changes that you’ve made – now to save your program:
1. Press the WRITE button. The name display indicates “*WRITE*”, and the BANK display and PROGRAM LED’s 1–4 will
flash.
2. Use VALUE KNOB 1, the ▲/▼ buttons, or the BANK UP/DOWN switches to select the bank you want to use; then
use the </> buttons, or PROGRAM SELECT switches to select the destination program 1–4.
3. Press the WRITE button once again. The program will be saved, the name display will indicate “COMPLETE,” and
you’ll return to Program Select mode.
!
The newly-saved program writes over the previous contents of that bank/program. If you decide not to store your
new program, press the EXIT button to cancel the procedure. Note that if you switch to a different program or turn
off the power without storing the Program you edited, your changes will be lost.
I
I
n
n
d
d
i
i
v
v
i
i
d
d
u
u
a
a
l
l
M
M
o
o
d
d
e
e
In this mode, you can individually turn each effect type on or off just as if you were using a collection of stomp boxes. You
can select INDIVIDUAL mode from any program.
1. To enter INDIVIDUAL mode from PROGRAM SELECT mode, press and hold the BANK UP switch for about one
second; the LED above the BANK UP switch will light green.
Here’s how to switch the pre-effect and reverb on or off while you’re playing:
2. Press the “program select” switch 1 to turn the pre-effect on/off. The LED 1 lit/ dark state indicates the on/off
status of the pre-effect.
3. Press the BANK DOWN switch to turn the reverb on/off. The LED at the upper left of the BANK DOWN switch will be
lit or dark to indicate the reverb’s on/off state.
4. To exit INDIVIDUAL mode, press the BANK UP switch, and the green LED will go dark (not lit).
E
E
x
x
p
p
r
r
e
e
s
s
s
s
i
i
o
o
n
n
T
T
a
a
r
r
g
g
e
e
t
t
Q
Q
u
u
i
i
c
c
k
k
A
A
s
s
s
s
i
i
g
g
n
n
Here you can easily assign many effect parameters of the AX3000G to its expression pedal for real time live control! For
example, you can assign the speed of a modulation effect, time of a delay, or mix of the reverb to the expression pedal.
And of course, the expression pedal can also act as a volume pedal or wah pedal effect.
As an example, let’s assign the Pitch parameter of the PITCH SHIFTER to the expression pedal:
1. Use the Modulation MODEL SELECTOR to choose the PITCH SHIFTER.
2. Rotate VALUE KNOB 1 or use the </> buttons to select the “PITCH” parameter. (PITCH” will be indicated in the
LCD)
3. In this state, press and hold the EXP/CTL button for one second, the name display will indicate “COMPLETE”.
That’s it! The PITCH parameter has now been assigned to the expression pedal, letting you control the amount of PITCH
SHIFT.