KORG EASYSTART AX3000G User Manual
Page 5
AX3000G EasyStart
5
Step 2 has been changed from -9 to -8, and step 5 from 3 to 4 (this changes it to a major arpeggio)
The ESS settings are as follows
:
SMOOTH STEPMODE STEP1 STEP
2 STEP
3
STEP 4
STEP 5
STEP 6
STEP 7
0 7-A
-12
-8
-5
0
4
7
12
Pitch shifter: Pitch=0, Fine=0, tracking=80, direct=0.0, effect=7.0
Delay:
2 Tap Delay
Time: 756, Feedback 4.4, Tone 7.9, Tap Time 5.0, Mix 4.4
Reverb:
Slap… Time=7.7, Lo Damp 3.7, High Damp 5.4, Pre Delay 0, Mix 4.5
T
T
h
h
e
e
C
C
o
o
n
n
t
t
r
r
o
o
l
l
S
S
w
w
i
i
t
t
c
c
h
h
You can assign the control switch to function in a variety of ways. It can act as an on/off for your effects/amp/cab models; a
tap tempo for modulation or delay, or even as a trigger for the ESS. Below is a list of the Control Switch functions. You can
make the following settings independently for each program for extra flexibility!
Press the EXP/CTL button and use VALUE KNOB 5 to select the effect you want to control, and then press EXIT to
return to Program mode…
Control Switch Effect On/Off:
Control Switch Effect Control:
• “I/ON OFF” External Insert effect on/off
• “P/ON OFF” Pre-effect on/off
• “A/ON OFF” Drive/Amp model on/off
• “M/ON OFF” Modulation effect on/off
• “D/ON OFF” Delay effect on/off
• “R/ON OFF” Reverb effect on/off
Control Switch Tap tempo:
• MOD TAP” Modulation TAP TEMPO
• DLY TAP” Delay TAP TEMPO
• “FLN TRIG” Activates Classic Flanger LFO
• “HOLD DLY” Activates HOLD of Hold Delay
• “FREEZ” Activates Freez of Freez effect
• “ESS CTL1” Turn ESS on/off
• “ESS CTL2” Turn the effect being controlled by ESS on/off
• “ESS TAP1” Tap tempo to specify the time between each
sequence step
• ESS TAP2” Tap tempo to specify the time between step 1 and the
last step of the sequence.
• “ESS TRIG” Restart step sequence from step 1
!
ESS TAP1, ESS TAP2, and ESS TRIG will do nothing if the SPEED of the step effect is set to PEdL.
R
R
e
e
s
s
t
t
o
o
r
r
i
i
n
n
g
g
t
t
h
h
e
e
F
F
a
a
c
c
t
t
o
o
r
r
y
y
P
P
r
r
e
e
s
s
e
e
t
t
P
P
r
r
o
o
g
g
r
r
a
a
m
m
s
s
Here’s how you can restore the AX3000G’s programs and settings to the state in which it was shipped from the factory:
1. While simultaneously holding down the ▲/▼ buttons and the EXIT switch, power-up the AX300G. The Bank Display
will read “P”, the LED 1–4 buttons will flash, and the name display will ask “RELOAD?” Release the ▲/▼ buttons and
the EXIT switch.
!
If at this point, you decide that you really don’t want to execute this operation, press the EXIT switch.
2. Press the WRITE button. The name display will show “LOADING,” and the factory data will begin reloading.
When completed, the name display will indicate “COMPLETE,” and the AX3000G will automatically switch to Program
Select Mode.
!
If there are any settings you want to keep, you should first use the Backup Program Data function (programs can also be
saved via our free AX3000G Editor/Librarian software; available at www.korg.com/AX3000G), or write down your settings
using the Original Value icon. See the AX3000G Owner’s Manual for additional information on using the Backup Program
Data function/ Original Value icon.
For more information, see your AX3000G Owner’s Manual, and be sure to visit
www.korg.com/AX3000G for more tips and tricks!!