Information channels – Kenwood TH-F6A User Manual
Page 25
20
6 MEMORY CHANNELS
INFORMATION CHANNELS
10 Information channels are available for storing
radio broadcasting service frequencies, such as
weather radio stations and community FM
broadcasting stations. For your conveniences,
pressing [INFO] instantly recalls the Information
channel to B-band. The following frequency data is
stored by default.
r
e
b
m
u
N
l
e
n
n
a
h
C
e
m
a
N
y
r
o
m
e
M
/
e
d
o
M
/
y
c
n
e
u
q
e
r
F
A
6
F
-
H
T
E
7
F
-
H
T
1
–
I
/
M
F
/
z
H
M
0
5
5
.
2
6
1
R
E
H
T
A
E
W
)
y
t
p
m
E
(
a
t
a
d
o
N
2
–
I
/
M
F
/
z
H
M
0
0
4
.
2
6
1
R
E
H
T
A
E
W
3
–
I
/
M
F
/
z
H
M
5
7
4
.
2
6
1
R
E
H
T
A
E
W
4
–
I
/
M
F
/
z
H
M
5
2
4
.
2
6
1
R
E
H
T
A
E
W
5
–
I
/
M
F
/
z
H
M
0
5
4
.
2
6
1
R
E
H
T
A
E
W
6
–
I
/
M
F
/
z
H
M
0
0
5
.
2
6
1
R
E
H
T
A
E
W
7
–
I
/
M
F
/
z
H
M
5
2
5
.
2
6
1
R
E
H
T
A
E
W
8
–
I
/
M
F
/
z
H
M
0
5
6
.
1
6
1
R
E
H
T
A
E
W
9
–
I
/
M
F
/
z
H
M
5
7
7
.
1
6
1
R
E
H
T
A
E
W
0
–
I
/
M
F
/
z
H
M
5
7
2
.
3
6
1
R
E
H
T
A
E
W
You can revise the default channel data, such as the
receiving frequencies, modes, and memory names.
RECALLING AN INFORMATION CHANNEL
Press [INFO] to recall the Information channels.
•
“I–n” appears, where “n” represents the
Information channel number from “0” ~ “9”.
•
If the B-band is selected for operation, you can
turn the Tuning control or press [ ]/ [ ] to select
other Information channels. If the A-band is
selected for operation, press [A/B] to move the
operation band to the B-band and then select a
different Information channel.
•
To exit the Information channel mode, press [A/B]
to select the B-band then press [VFO] or [MR].
Note: If you press [MN<->f], you can display the receiving frequency
in place of the memory name.
TH-F7E only: As default, no frequency data is stored in the
Information channel. Store the frequency data before using the
Information channels. Otherwise, an error beep sounds.
REPROGRAMMING THE INFORMATION CHANNEL
1 Press [VFO].
2 Select a desired frequency and mode.
3 Press [F].
4 Turn the Tuning control or press [ ]/ [ ] to select
the memory channel (I–0 to I–9) in which you want
to store the data.
5 Press [MR] ([ ] or [MNU]).
•
A long beep sounds and the Information
channel data is now revised.
Note:
◆
When you perform the Full reset {page 50}, all the Information
channels recover the factory default values.
◆
If you clear an Information Channel data {page 16}, the factory
default value is recovered.
◆
You can also transfer the Information Channel data to the VFO
or another memory channel.