Speaker setup, Audio setup, Exit audio setup – Kenwood KDV-5234 User Manual
Page 44: Fine adjust the system q value to the speakers, Set to standby mode, Select "standby, Set to the speaker matching mode, Sets up volume offset, dual zone function, etc, Start audio setup, Select features to set
44
KDV-5234
4
Exit audio setup
Q
AM
SETUP
AUD
VOL
ATT
MENU
SCAN
STOP
M/S
RDM
REP
F.SEL
M.RDM
DISP
/PTY
SW
AME
TI
FM
SCRL
SRC
• If a volume offset is set for each source with "V-OFF", the
volume will be nearly the same for all sources when the
source is changed.
• When "2ZON" is ON ("DVD"/"AUX"), you can only set "V-
OFF" and "LOUD".
• If the dual zone function is used, different sources can be
output from the front speakers (source of this unit) and
the rear speakers (disc source of this unit or the sound
input to the built-in AUX).
• For "LPF" and "PHAS", the feature "SWPRE" needs to be
set to "SW" (subwoofer) in advance in the menu setup,
and the subwoofer output to ON. For details on how to
set up "SWPRE", refer to <Menu setup> (page 50), and for
subwoofer output, refer to <Subwoofer output control>
(page 45).
• "PHAS" cannot be set up when "LPF" is set to "THRU".
• "AVOUT" can be set when the feature "SWPRE" in <Menu
setup> (page 50) is set to "AV".
Speaker setup
Fine adjust the System Q value to the speakers.
1
Set to STANDBY mode
Q
AM
SETUP
AUD
VOL
MENU
SCAN
STOP
M/S
RDM
REP
F.SEL
M.RDM
OFF
DISP
/PTY
SW
SRC
STANDBY
Select "STANDBY".
2
Set to the speaker matching mode
Q
AM
SETUP
AUD
VOL
ATT
MENU
SCAN
STOP
M/S
RDM
REP
F.SEL
M.RDM
DISP
/PTY
SW
AME
TI
FM
SCRL
SRC
Audio setup
Sets up volume offset, dual zone function, etc.
1
Start audio setup
Q
AM
SETUP
AUD
VOL
ATT
MENU
SCAN
STOP
M/S
RDM
REP
F.SEL
M.RDM
DISP
/PTY
SW
AME
TI
FM
SCRL
SRC
2
Select features to set
Q
AM
SETUP
AUD
VOL
ATT
MENU
SCAN
STOP
M/S
RDM
REP
F.SEL
M.RDM
DISP
/PTY
SW
AME
TI
FM
SCRL
SRC
Each time the knob is rotated, the type
changes in the following order.
Feature
Setting range
HPF
Specifies the front high-pass filter cutoff
frequency.
HPR
Specifies the rear high-pass filter cutoff
frequency.
LPF
Specifies the low-pass filter cutoff frequency.
PHAS
Specifies the subwoofer phase.
V-OFF
Adjusts the volume difference between sources.
LOUD
Corrects treble and bass when the volume is low.
AVOUT
Specifies the output level of the AV OUT terminal.
2ZON
Turns the dual zone function ON/OFF.
3
Set up each feature
Q
AM
SETUP
AUD
VOL
ATT
MENU
SCAN
STOP
M/S
RDM
REP
F.SEL
M.RDM
DISP
/PTY
SW
AME
TI
FM
SCRL
SRC
The setting range of each item is as follows:
Features
Setting range
HPF/HPR
THRU (Filter Off)/40/60/80/100/120/150/
180/220 (Hz)
LPF
50/60/80/100/120 (Hz)/THRU (Filter Off)
PHAS
REV (180˚)/NML (0˚)
V-OFF
-8 – 0
LOUD
OFF/ON
AVOUT
-15 – 0
2ZON
OFF/DVD/AUX
Audio Control