Wireless remote control(k-type only), Preparation, Control operation – Kenwood TS-2000 User Manual
Page 90: Wireless remote control (k-type only)
82
15 OPERATOR CONVENIENCES
WIRELESS REMOTE CONTROL
(K-type ONLY)
If you have a Kenwood TH-D7A handheld transceiver,
you can use it to remotely control the 144 MHz and
440 MHz bands of the TS-2000(X) transceiver, using
FM mode. You will be controlling one band on the
TS-2000(X) transceiver while sending DTMF tones to
the other band from the remote control transceiver.
This function is useful, for example, when you want to
control the VHF/ UHF FM repeater function of the
TS-2000(X) transceiver from a location outside your
home or vehicle.
Note:
◆
To remotely control the TS-2000(X), you can also use a handheld
transceiver which does not have a remote control function, but a
DTMF function. You must, however, manually send DTMF tones
for control code strings. Skip steps 1 and 3 in “PREPARATION”,
below.
◆
FCC rules permit you to send control codes only on the 440 MHz
band.
PREPARATION
Assuming that the 144 MHz band of the TS-2000
transceiver will be controlled.
On the control transceiver:
1 Program a 3-digit secret number.
•
If you are using a TH-D7A, see “WIRELESS
REMOTE CONTROL” in its instruction manual.
2 Select the transmit frequency on the 440 MHz
band.
3 Enter the Remote Control mode.
On the TS-2000 transceiver:
4 Access Menu 61C, and select the same secret
number that you selected in step 1.
5 Select the receive frequency on the 440 MHz
band of the sub-receiver.
•
Mate this frequency with the transmit frequency
on the control transceiver.
6 Select the 144 MHz band as the TX band or
Control band for the main transceiver.
7 To have the TS-2000(X) transceiver send a control
acknowledgment to the handheld, access Menu
61D and select “ON”.
•
DTMF tones which represent the secret
number will be used as an acknowledgment.
8 Access Menu 61E and select “ON”.
•
“
” appears when the TS-2000(X) enters
Remote Control mode.
CONTROL OPERATION
When in Remote Control mode, the DTMF keys of the
control transceiver will function as shown in the table
below. Each time you press the desired key, the
transceiver will automatically enter transmit mode and
send the corresponding command to the mobile.
Note: If you are using a transceiver without a remote control
function, manually send “AXXX#YA#” where “XXX” is your 3-digit
secret number and “Y” is a single-digit control command. If you do
not add ”A#” on the end, you can skip sending “AXXX#” next time;
however, the mobile may be accidentally controlled by other stations.
1
N
O
S
C
D
9
R
M
2
N
O
E
N
O
T
0
W
O
L
3
N
O
S
S
C
T
C
A
R
E
T
N
E
4
F
F
O
S
C
D
B
L
E
S
E
N
O
T
5
F
F
O
E
N
O
T
C
N
O
R
E
T
A
E
P
E
R
6
F
F
O
S
S
C
T
C
D
F
F
O
R
E
T
A
E
P
E
R
7
L
L
A
C
N
W
O
D
8
O
F
V
#
P
U
To change the transmit/ receive frequency:
([VFO]
➡
[ENTER]
➡
[0] ~ [9] (enter the necessary
digits)
➡
[ENTER]) or ([VFO]
➡
[UP]/ [DOWN])
To recall a memory channel:
([MR]
➡
[ENTER]
➡
[0] ~ [9] (enter the necessary
digits)
➡
[ENTER]) or ([MR]
➡
[UP]/ [DOWN])
To change the tone (or CTCSS) frequency:
([TONE SEL]
➡
[0] ~ [9] (enter 2 digits; ex. [0], [5])
➡
[TONE SEL])
•
Use Nos. 01 to 38 shown in the table on page 35.
•
First activate the Tone or CTCSS function. You
can select a separate tone frequency for the Tone
and CTCSS functions.
Note: While in Wireless Remote Control mode, you can perform only
the following operations on the TS-2000(X) transceiver.
•
Transmit
•
Acknowledge ON/ OFF
•
Secret Number Change
•
Partial/ Full Reset