KORG TONEWORKS AX5G - Manual (Page 9)

9
AX5G Owner’s manual
Selecting and adjusting sub-parameters
[PRE FX-PARAM], [DRIVE/AMP-PARAM], [MOD-PARAM], [DELAY/
REV-PARAM]
Here’s how to edit the sub-parameters of the effect you’ve selected for each
of the [PRE FX], [DRIVE/AMP], [MOD], and [DELAY/REV] categories.
When you press the [
▲ ] or [ ▼ ] buttons, the program/value display will indicate
a value of P1–P5, and the LED in the upper part of the program down pedal
will light (or blink) to indicate that the parameter type is being displayed.
For the sub-parameters that correspond to P1–P5, refer to p.50 “Param-
eter List”.
Now you can use the value dial to edit the sound by adjusting the vari-
ous sub-parameters. At this time, the program/value display will indicate
the parameter value, and the LED in the upper part of the program up
pedal will light to indicate that the parameter value is being displayed.
If the effect is turned off, the program/value display will indicate “ ”
when you set the function selector to a [PARAM] position for that cat-
egory. If you want to edit the parameters of that effect, simultaneously
press both the [
▲ ] and [ ▼ ] buttons to turn the effect on.
■ Quick guide
To select an effect and edit it to your taste, you should first adjust the main
parameters, and then adjust sub-parameter P1. In most cases, you’ll be
able to get the sound you want by adjusting these two parameters.
[LEVEL/NR/CAB/PEDAL]
Set the function selector to this position when you want to adjust the
program level, noise reduction, or cabinet modeling. Then press the [s]
or [t] buttons to cycle the display through “
”(program level), “ ”
(NR sensitivity), “ ”(cabinet), and “ ”, “ ”(Expression pedal
target range). Use the value knob to adjust each parameter.
: Use the value knob to adjust the program level (0.0–10). A setting
of 5.0 is the standard value. Some effect settings may cause clip-
ping. If this occurs, lower the program level.
: Adjust the noise reduction sensitivity (0.0–10) so that you don’t hear
noise (hiss) when you’re not playing your guitar.
Depending on the guitar you’re using, notes may be cut off if you raise the
noise reduction value excessively. Adjust this so notes ring out naturally.
: Select the type (C0–C9) of cabinet modeling.
You can’t edit the cabinet model if the drive/amp model is off. In this
case, the LED will indicate “
”.
Cabinet modeling is associated with the drive/amp model. It works
only if the drive/amp model is turned on. When you change the drive/
amp model type, the most suitable cabinet model is selected auto-
matically.
Cabinet modeling is associated with the drive/amp model. It works
only if the drive/amp model is turned on. When you change the drive/
amp model type, the most suitable model is selected automatically.
: Specify the value of the parameter when the expression pedal is
fully returned toward yourself.
: Specify the value of the parameter when the expression pedal is
fully advanced away from yourself.
Effect/parameter type and parameter value display
When you press the Program Down switch in Edit mode, the program/
value display will indicate the effect type or parameter type (F0–F9, d0–
d7, A0–A7, P1–P5). When you press the Program Up switch, the pro-
gram/value display will indicate the parameter value. This gives you a
convenient way to check the current settings.
Expression pedal settings
Make the program/value display show the effect parameter (F0–F9, d0–
d7, A0–A7, P1–P5). Make sure that the LED of the program up pedal or
program down pedal is blinking, and then hold down the pedal setting
switch for about one second.
You can’t use the expression pedal to control a parameter for which the
program up pedal or program down pedal does not blink.
The program/value display will briefly indicate “ ”(Complete), and you’ll
be able to use the expression pedal to control the effect parameter.