Little Wonder 900 - Manual (Page 4)

Engine . . . . . . . . . . . . . . . . . . . . . . . . . . . .see manufacturers manual
Transmission . . . . . . . . . . . . . . . . .hydrostatic, infinite speed control
Blade . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .notched, spring steel
Bearings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .roller
Frame . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .welded, formed steel
Gauge Wheel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .single
Cutting Depth . . . . . . . . . . . . . . . . . . . . . . . . .1" - 4.5" (2.5 - 11.4 cm)
Depth Adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .pin, position
Total Width . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .43" (109.2 cm)
Total Length . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .51" (129.5 cm)
Total Height . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .45" (109.2 cm)
Blade Diameter . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16 1/4" (41.3 cm)
Shipping Weight . . . . . . . . . . . . . . . . . . . . . . . . . . . .365 lbs. (165 kg)
Section 1
GENERAL INFORMATION
HIGHLIGHTED INFORMATION
Information that is of special importance has been
highlighted with headings in boldface type.
Danger, Warning, and Caution identify safety-
related information and can be further identified
by the safety alert symbol . Important identi-
fies information requiring special attention since it
deals with the possibility of damage to part or
parts of BedShaper
® machines. Note identifies
information worthy of special attention.
MODEL AND SERIAL NUMBER LOCATION
Both the model number and serial number are
located on the manufacturer’s plate located on
the mainframe of the BedShaper
® (See Photo 1-1).
The number in the top box is the model number.
The number in the bottom box is the serial num-
ber. Please use these numbers when ordering
replacement parts or when obtaining mainte-
nance assistance. Record these numbers in Table
1-1 for easy access.
Fill In Information:
BedShaper ®
Model Number__________________________
BedShaper ®
Serial Number__________________________
Date of Purchase________________________
Dealer Name___________________________
INTENDED USE
BedShaper ® machines are intended to shape and
edge the perimeter of a landscaped flower bed or
sand trap. It is further intended that the machine
be operated by a trained individual who is familiar
with commercial landscape equipment, standing
behind the machine at the controls.
Section 2
SPECIFICATIONS
Photo 1-1 Table 1-1
LEFT AND RIGHT
Left and right references in this manual are made
from the operator’s position looking in the
direction of travel.
Specifications are subject to change without notification.
1
Repair parts for your
BedShaper
® are listed in
Section 7, ILLUSTRATED
PARTS BREAKDOWN, and
are available through your
Little Wonder
® dealer. The
parts list was developed as
a general overview. Contact
your Little Wonder
® dealer
for the most up to date
information.
Little Wonder ®