Life Fitness CLST - Manual (Page 6)

4
IMPORTANT !
DO NOT DISCARD THE SHIP KIT LOCATED ON TOP OF THE DECK AND BELT. ALL NECESSARY COMPONENTS
NEEDED TO COMPLETE THE INSTALLATION ARE LOCATED IN THE SHIP KIT.
NE JETEZ PAS LE KIT D'EXPÉDITION PLACÉ SUR LE DESSUS DU PLATEAU ET SUR LE TAPIS. IL CONTIENT
TOUS LES ÉLÉMENTS NÉCESSAIRES POUR L'INSTALLATION.
IMPORTANT !
Check the belt edge under the treadmill to verify the belt does not interfere with lifespring brackets and the belt is
properly set within the belt guides.
1. Remove the four S CREWS (A) securing the F RONT G RILL (B)
to the F RAME (C). Remove the F RONT G RILL and set it aside.
2. Remove the four S CREWS (D) securing the M OTOR C OVER (E).
Lift and remove the M OTOR C OVER and set it aside.
3. Locate the L EFT U PRIGHT (1). Lay the L EFT U PRIGHT across
the belt and deck with the notched end near the L EFT U PRIGHT
M OUNTING B RACKET (F).
4. Unwrap the M AIN W IRE H ARNESS (G) leading from the L EFT
U PRIGHT M OUNTING B RACKET (F). Feed the M AIN W IRE
H ARNESS through the L EFT U PRIGHT (1). Carefully tilt the L EFT
U PRIGHT upwards and position the notched end of the L EFT
U PRIGHT over the L EFT U PRIGHT M OUNTING B RACKET . With the
L EFT T OP M OUNTING P LATE (H) directed forward, slide the
L EFT U PRIGHT down over the L EFT U PRIGHT M OUNTING
B RACKET and pre-installed B OLT and W ASHER until it rests on
the F RAME (C). Secure the L EFT U PRIGHT to the L EFT U PRIGHT
M OUNTING B RACKET using two B OLTS and W ASHERS (20 & 24).
Use one B OLT and W ASHER on the inside of the L EFT
U PRIGHT and one B OLT and W ASHER on the front side of the
L EFT U PRIGHT . Leave the B OLTS loose at this time.
Note: Be careful not to damage the M
AIN W IRE H ARNESS (G)
when routing it through the L EFT U PRIGHT (1) or when
sliding the L EFT U PRIGHT over the L EFT U PRIGHT M OUNTING
B RACKET (F).
Note: Be sure the pre-installed washer is on the outside
of the L
EFT U PRIGHT (1) when sliding it down to rest on
the F RAME (C).
5. Locate the R IGHT U PRIGHT (2). With the R IGHT T OP M OUNTING
P LATE (J) directed forward, slide the R IGHT U PRIGHT down
over the R IGHT U PRIGHT M OUNTING B RACKET (K) and pre-
installed B OLT and W ASHER until it rests on the F RAME (C).
Secure the R IGHT U PRIGHT to the R IGHT U PRIGHT M OUNTING
B RACKET using two B OLTS and W ASHERS (20 & 24). Use one
B OLT and W ASHER on the inside of the R IGHT U PRIGHT and
one B OLT and W ASHER on the front side of the R IGHT
U PRIGHT . Leave the B OLTS loose at this time.
Note: Be sure the pre-installed washer is on the outside
of the R
IGHT U PRIGHT (2) when sliding it down to rest on the F RAME (C).