Liebherr 7082 344-01 - Manual (Page 10)

20
BN/SBN/es...6
Instructions for installation
and modification
Installation instructions:
- Do not install the appliance directly next to another refrig-
erator or freezer. This is important to prevent condensation
and consequential damage resulting from it.
- This does not apply to Side-by-Side models (SBS). They
are designed for Side-by-Side installation with another
refrigerator/freezer.
The "Installation instructions for Side-by-Side combina-
tions" are supplied in the accessories bag for the SBS
freezer or the appliance with a freezer compartment.
Installation dimensions
For the external dimensions of the appliance, see fig. S.
Changing over door hinges
On appliances which are intended for individual installation
the door hinges can be changed from one side to the other.
On SBS appliances in stainless steel finish, which are de-
signed for Side-by-Side installation, the door hinges must not
be transferred to the other side!
W
Only change over door hinges when mains plug is discon-
nected!
W
Fig. T. With the door open, lever out plinth panel
1
on the
hinge side with a screwdriver and remove from front.
- Lever out cover
2
with a screwdriver. Close door.
- Unscrew screw M5
3
.
W
Pull hinge component
4
with hinge pin
5
out from under-
neath and remove.
- Open door, lift out at bottom and remove.
- Pull middle hinge pin
6
out from underneath.
- Tilt out top door and lift off from underneath (with version I,
do not lose spacer sleeve
9
).
W
Transfer all hinge components onto the other side:
W
Top: depending on version, proceed as follows:
Version I (visible operating panel): Lever out covers
8
with
a screwdriver at the front and remove at an angle from be-
low. Remove hinge pin
7
and insert on the opposite side.
Use the hexagon socket on the open-ended spanner pro-
vided (spanner width 5). Fit covers
8
again: insert at rear
and click into place at front.
Version II (concealed operating panel): Lift up cover
8
on
handle side, push outwards; lift up cover on hinge side and
pull off.
- Unscrew earthing plate
cm
: first earthing screw
cl
, then
inner retaining screw
cq
.
- Unscrew hinge
9
: first undo earthing screw
cl
, then re-
taining screws
cq
. Fit hinge
9
to opposite side: for easy
assembly, fit hinge from above and first tighten with the up-
per retaining screw
cq
M5, then screw
cq
and finally earth-
ing screw
cl
M4.
- Turn earthing plate
cm
through 180° and screw tight again
on the new handle side: first retaining screw
cq
, then earth-
ing screw
cl
.
- Insert hinge pin
7
in the other retaining hole. Use the hex-
agon socket on the open-ended spanner provided (span-
ner width 5).
- Fit covers
8
again: insert hinge-side cover by sliding out-
wards and click into position; insert handle-side cover by
sliding inwards and click into position.
W
Centre: Change over cover
bl
with hinge
bm
: unscrew
screws, lift off cover
bl
and hinge
bm
to the side, turn
through 180° and replace on the other side, remove
hinge bushing
bn
and re-insert from top.
W
Bottom: Using a screwdriver, remove the spacer
bo
and
replace on the other side.
Your appliance is designed and manufactured for a long life
span and reliable operation.
If a malfunction nonetheless occurs during operation, check
whether it is due to an operating error. Please note that even
during the warranty period the resultant servicing costs in this
case will have to be borne by the owner.
You may be able to rectify the following faults by checking the
possible causes yourself:
Malfunction Possible cause and remedy
________________________________________________
Appliance does not work, display is off
- Is the appliance switched on properly?
- Is the mains plug properly inserted in the socket?
- Is the socket fuse intact?
The interior light does not come on
- Is the BioFresh compartment switched on?
- Has the door been open for more than 15 minutes?
- The bulb is defective. Change the bulb as described in
"Interior light".
Loud running noise
- Is the appliance standing firmly on the floor, or does the
compressor cause nearby items of furniture or objects to
vibrate? If necessary, move the appliance slightly, align by
adjusting the adjustable feet, or move bottles and contain-
ers apart.
- Burbling noises are normal. These are caused by the
refrigerant flowing round the refrigerant circuit.
A short clicking sound: This will be heard whenever the
refrigeration unit (the motor) switches on or off auto-mati-
cally.
Motor noise: This will be slightly louder for a brief period
when the refrigeration unit switches on. The refrigerat-
ing capacity will increase when the SuperFrost function is
activated, fresh food has just been placed in the appliance
or the door has been left open for a while.
The audible warning signal sounds, the temperature is
not cold enough
- Have you put too much fresh food into the freezer without
activating SuperFrost? (See "SuperFrost")
- Does the door close properly?
- Is the appliance sufficiently well ventilated?
Clear ventilation grilles if necessary.
- Is the ambient temperature too hot?
(See "Safety regulations")
- Has the appliance been opened too often or left open
too long?
- If applicable, wait until the appliance reaches the
required temperature itself.
appears in the display
- There has been a power failure; proceed as described in
"Power failure/FrostControl display".
The outside of the appliance may feel warm in places
- That is quite normal. The heat from the cooling circuit is
used to avoid the formation of condensate.
Customer service and type plate
If none of the above causes apply and you cannot rec-
tify the fault yourself, or if the temperature display reads
"
F 0
" to "
F 5
", this means that there is a fault. Please
contact your nearest customer service department (see en-
closed list for addresses). Give the fault number displayed,
together with the
type designation
1
,
service number
2
and
appliance number
3
as given on the type plate, so
as to ensure rapid, accurate
servicing. The type plate is
located inside the appliance on
the left-hand side.
Leave the appliance shut until
the customer service engineer
arrives so as to prevent any further cold loss.
Troubleshooting