Land Pride RCM6510 - Manual (Page 50)

48
Section 7: Features & Benefits
RC5510 & RC6510 (540 RPM) RCM5510 & RCM6510 (1000 RPM) Rotary Cutter 330-057M 5/29/13
Table of Contents
* Years 6 & 7 Parts Only
RC(M)5510 & RC(M)6510 Models
Features Benefits
Surpassed rugged
industry standards All Land Pride Cutters have been designed and tested and meet rigorous voluntary
testing procedures specified by ANSI.
Factory assembled Saves customer set-up time and money.
7 Year gearbox warranty* Shows confidence in gearbox integrity.
250 HP Divider gearbox
210 HP center & wing gearboxes A rugged heavy built gearboxes capable of handling heavy cutting applications.
Gearbox Seal Protection Gearbox bottom seal protection for longer bearing life.
2 3/8" Output gearbox shaft Large output shaft handles shock loads better.
Input driveline: Cat. 5 CV Holds up to shock loads and harsh mowing conditions.
Cat. 5 intermediate & Cat. 4 wing
drivelines with slip-clutches Driveline is sized right for the intended cutting capacity. Slip-clutch will slip under load
instead of twisting the driveline.
Star profile drive shafts Star profile spreads load out to many points on the shaft. More apt to resist bending and
twisting under shock loads and harsh mowing conditions.
Easy Greasable drivelines Drivelines have access holes for greasing the U-joints and to grease the inner profiles.
4 Plate slip-clutch Protects drivelines and gearboxes by slipping clutches rather than twisting the driveline
when impacts are encountered.
High blade tip speed
(See specifications for actual FPM) Allows clean cutting of material.
6" Blade overlap Eliminates skipping during turns.
High cutting capacity 55 Series
65 Series Can cut brushy areas with saplings up to 4".
Can cut brushy areas with saplings up to 4 1/2".
Pre-cut chamber Allows grass and vegetation to stand back up prior to cutting for a more complete cut.
12" Deck height Handles heavy cutting, which reduces balling-up of cut material under the deck.
3/16" Stump jumper backed
with a 1" thick mounting bar Heavy round stump jumper with bottom gearbox seal protector. Can hold up to tough
conditions.
10 gauge smooth deck top Reduces accumulation of debris and is easier and faster to clean.
7 Gauge smooth deck bottom Heavy deck design holds up to harsh conditions. No bottom obstructions.
Replaceable 1/4" side skirt Reduces debris piercing possibilities. Can be replaced if damaged.
Self-leveling hitch Reduces drawbar wear by keeping hitch level while going through ditches.
Hinged wing section Allow you to shape the cutter to the job. Ideal for rough ground where hillsides, ditches
and hollows can cause uneven cutting.
Left side weight box Serves as counterweight for balance when raising the wing.
1" Solid hinge rods Larger diameter hinge rod gives greater strength to the cutter from front to rear, and in
the hinge area itself.
Wing transport lock Holds transport wing in the folded-up position in case of hydraulic pressure loss.
Enclosed front to rear dual leveling
rods Dual leveling rods enable the cutter to pull equally on the rear axle during travel over
rough terrain. Many competitors only use one leveling rod.
5-Bolt hubs 5-Bolt hubs makes the wheel assembly more durable and longer lasting.
Drain holes in wheel rims Allows water to drain from wheels mounted on the folded-up wing.
Helps prevent paint deterioration and rusting to the wheel rims.
Spring-cushioned center-axle Protects unit from bumps and ground shock.
Replaceable wheel spindles Wheel spindles can be replaced when damaged without replacing the entire axle.
Simply remove two bolts to replace damaged spindle.
Double swivel hitch Great for uneven terrain, reduces drawbar wear.
Bar-Tite Hitch option Ideal for extreme conditions. Clamps tight to drawbar eliminating drawbar wear.
Wheel options Laminated tires: Eliminates flats.
Airplane tires without foam filling: Give better cushion while transporting.
Airplane tires with foam filling: Give better cushion while transporting and can’t go
flat.
Walking Tandem option Better flotation and smoother ride on rougher terrain.
Deck rings (optional) 1/2" x 3" full welded deck ring keeps blades from damaging the deck.
Section 7: Features & Benefits