Conserver ces instructions, Información general de seguridad, Operation – Lasko 758000 User Manual

Page 3

Advertising
background image

New 4/07

6

758000ES

New 4/07

3

758000ES

MODEL 758000

TIMER: (Figure 2)

The Timer Function may be activated when the Heater is in any speed or
temperature. This function allows you to set the length of time the Heater
will run before turning itself off, from 1 hour to 7 hours. Pressing the

Timer

Button will increase the length of time, in combinations of 1, 2 and 4
hours. Continuously pressing the button will result in the timer being set
for 7 hours. The Heater will turn off when the set time has elasped. The
unit can be turned back on by pressing the

Power Button.

OPERATION

1. Carefully remove the Heater from the bag and the carton.
2. Place the Heater on a firm, level surface.

WARNING:

Plastic or rubber tabs, like the feet on this unit, may

stick to furniture surfaces and/or hardwood floors. The unit may leave
a residue that could darken, stain or leave permanent blemishes on
the finish of certain furniture surfaces, including wood surfaces, and/or
hardwood floors.
3. Plug the cord set into a 120 volt outlet.

Be sure that the plug fits tightly into outlet.

When plugs fit loosely into receptacles, they may slip

partially or completely out of the receptacle with only

the slight movement of the attached cord. Receptacles

in this condition may overheat and pose a serious fire

hazard; if covered by a curtain or drape, the fire hazard

is even greater.

4. When the Heater is initially plugged in, there will be a ‘beep’ and

the Power Light will come on indicating that there is power to the
unit. The Power Light will remain lit until the Heater is unplugged
from the electrical outlet.

5. Turn the Heater ON by pressing the

Power Button.

6. When initially turned on, the Heater will display the current

room temperature in ° Fahrenheit. Press the ( ) and ( )
buttons at the same time to change the display to ° Celsius. Press
the same two buttons together again to change the display back
to ° Fahrenheit.

7. Upon turning the Heater on, the unit will be in HIGH heat (1500

Watts) and will display the current room temperature

(Figure 1)

8. Press the Mode button for LOW heat (750 Watts).

9. See Thermostat section for Automatic Control instructions.
10.To turn the Heater OFF, press the

Power Button and unplug the

Heater from the electrical outlet.

THERMOSTAT:

Pressing the ( ) or ( ) button allows you to set the desired
temperature of the room. For increased efficiency, the Thermostat
will only run in High heat.

(Figure 3)

1. Press the ( ) to increase the desired set temperature or press the

( ) to decrease the desired set temperature.

2. When the air temperature reaches 2° above the set temperature,

the Heater will shut off.

3. When the air temperature reaches 1° below the set temperature,

the Heater will turn on.

NOTE: It is normal for the Heater “fan” to run for approximately 15
seconds after the Heater shuts off after reaching the set temperature.

LOUVER FUNCTION:

(Figure 4)

This Heater has a louver on the top front grill that allows for vertical
adjustment of air flow. Slide the louver control up or down to adjust
the air flow as desired.

Figure 1

   

    

Figure 2

Figure 3

Figure 4

Louver Function

1.

NO CONECTE EL CALEFACTOR A CUALQUIER OTRO DISPOSITIVO CONECTADO A UN CABLE, COMO UN CABLE DE CONTACTOS

MÚLTIPLES, PROTECTOR DE SOBRECARGAS, ADAPTADORES DE TOMACORRIENTES MÚLTIPLES O REFRESCANTES DE AIRE

TIPO TOMACORRIENTE. EL USO DE TALES DISPOSITIVOS PODRÍA CREAR UN RIESGO DE INCENDIO. CONECTE LA UNIDAD

DIRECTAMENTE A UN TOMACORRIENTE DE PARED DE 120V ÚNICAMENTE.

2.

EVITE EL USO DE CABLES DE ALARGUE PORQUE EL CABLE DE ALARGUE PODRÍA SOBRECALENTARSE Y PROVOCAR

UN RIESGO DE INCENDIO. SIN EMBARGO, SI USTED TIENE QUE USAR UN CABLE DE ALARGUE, MINIMICE EL RIESGO DE

SOBRECALENTAMIENTO USANDO EL CABLE MÁS CORTO POSIBLE Y GARANTIZANDO QUE ESTÉN AUTORIZADOS POR UL.

EL CABLE DEBE SER TRIFÁSICO CON CONEXIÓN A TIERRA CON UN TAMAÑO MÍNIMO NO. 14 AWG Y UNA CALIFICACIÓN NO

INFERIOR A 1875 VATIOS (15A). NUNCA USE UN CABLE DE ALARGUE ÚNICO PARA OPERAR MÁS DE UN CALEFACTOR.

ADVERTENCIA: Conexiones defectuosas al tomacorriente de pared pueden causar que el tomacorriente de pared se sobrecaliente.

Asegúrese que el enchufe del calefactor encaje firmemente en el tomacorriente antes de cada uso. Durante el uso, verifique para

asegurarse que el enchufe del calefactor no esté sobrecalentando. De ser necesario, haga que un electricista calificado revise y/o

reemplace el tomacorriente de pared.

3. Use este Calefactor solamente como se describe en este manual. Cualquier otro uso no recomendado por el fabricante podría causar

incendio, choque eléctrico o lesiones a personas.

4. Asegúrese que la habitación esté equipada con un detector de humo en funcionamiento.

5. Garantice que la fuente de alimentación eléctrica sea la adecuada a los requerimientos eléctricos del Calefactor.

6. Es necesario practicar extrema precaución al utilizar cualquier Calefactor cerca de o por niños o personas discapacitadas y cuando el

Calefactor esté funcionando sin atención.

7. Este electrodoméstico cuenta con un enchufe polarizado (una clavija es más ancha que la otra). Para reducir el riesgo de choque eléctrico,

este enchufe está diseñado para encajar en un tomacorriente polarizado solamente en un sentido. Si el enchufe no encaja perfectamente

en el tomacorriente, coloque el enchufe a la inversa. Si sigue sin funcionar, póngase en contacto con un electricista calificado. No intente

alterar esta característica de seguridad.

8. No ponga en funcionamiento ningún calefactor con un cable eléctrico o enchufe dañados, después que un calefactor haya funcionado

mal o haya sido arrojado o dañado en cualquier modo. Por favor contacte a Servicio al Cliente al 800-233-0268 de lunes a viernes de 8

am a 5 pm EST para obtener asistencia.

CONSERVER CES INSTRUCTIONS

Lea todas las instrucciones antes de usar este Calefactor.

INFORMACIÓN GENERAL DE SEGURIDAD

Al usar artefactos eléctricos, siempre deben tomarse precauciones básicas para reducir

el riesgo de incendio, choque eléctrico y lesiones a personas, incluyendo las siguientes:

9. Para desconectar el Calefactor, posicione los controles en APAGADO, luego retire el enchufe del tomacorriente.

10. Siempre desconecte el Calefactor cuando no esté en uso. Desconecte el cable eléctrico antes de reparar o trasladar el Calefactor.

11. No inserte ni permita que los dedos u objetos extraños se introduzcan en ninguna abertura o escape de ventilación ya que esto podría causar

un choque eléctrico, incendio o dañar el Calefactor. No bloquee ni altere el Calefactor de ninguna manera mientras esté en funcionamiento.

12. Para evitar un posible incendio, no bloquee las tomas o escapes de aire de ninguna manera. No coloque sobre superficies suaves como

una cama, donde las aberturas podrían resultar bloqueadas.

13. Siempre coloque el Calefactor sobre una superficie estable, lisa y nivelada mientras esté en funcionamiento para evitar la posibilidad de que

el Calefactor se sobrecaliente. Ubique el Cable Eléctrico de modo tal que el Calefactor u otros objetos no estén encima de él. NO coloque

el Cable Eléctrico debajo de alfombras. NO cubra el Cable Eléctrico con alfombrillas, alfombras de protección o similares. Coloque el Cable

Eléctrico lejos del paso de las personas en la habitación y donde no exista la posibilidad de que alguien se tropiece con el mismo.

14. Este Calefactor está CALIENTE cuando está en funcionamiento. Para evitar quemaduras, no permita que la piel desnuda toque las

superficies calientes. Siempre use la agarradera cuando traslade este Calefactor. Mantenga los materiales combustibles, tales como

muebles, almohadas, ropa de cama, papeles, vestimenta y cortinas por lo menos a 3 pies (0.9 m) del frente del Calefactor y manténgalos

por lo menos a 1 pie (0.3 m) de los costados y de la parte trasera.

15. Un Calefactor tiene partes calientes y arcos eléctricos o partes que producen chispas en su interior. NO use el Calefactor en áreas donde

se almacene o use gasolina, pintura o líquidos inflamables. NO use el Calefactor en lugares donde sustancias químicas inflamables o

explosivas, sean almacenadas, o en atmósferas húmedas. Este Calefactor está diseñado ÚNICAMENTE para uso general.

16. Este Calefactor no está diseñado para ser usado en lugares húmedos o mojados. Este Calefactor no está diseñado para usar en baños,

áreas de lavandería o lugares interiores similares. NUNCA ubique un Calefactor en un lugar donde podría caer dentro de una tina de

baño o cualquier otro recipiente de agua.

17. NO use Calefactores al aire libre.

18. Este Calefactor no es adecuado para usar en instalaciones de agricultura incluyendo áreas donde se almacene ganado, aves de corral

u otros animales. Por favor consulte el Articulo 547-7 (2002) del Código Eléctrico Nacional (NEC), o los códigos o normas estatales o

locales aplicables con relación a los requisitos eléctricos para edificios destinados a las agricultura.

ESTE CALEFACTOR NO CUMPLE

CON LOS REQUISITOS DEL ARTICULO 547-7 DEL NEC (2002)

19. Este Calefactor no es adecuado para usar en lugares peligrosos. Por favor consulte el Artículo 500 del Código Eléctrico Nacional (NEC), o

los códigos o normas estatales o locales aplicables con relación a los requisitos eléctricos para lugares peligrosos.

ESTE CALEFACTOR

NO CUMPLE CON LOS REQUISITOS DEL ARTICULO 500 (2002)

ADVERTENCIA: REDUZCA EL RIESGO DE INCENDIO O CHOQUE ELÉCTRICO – NO USE ESTE CALEFACTOR CON DISPOSITIVOS

DE CONTROL DE VELOCIDAD DE ESTADO SÓLIDO.

NO DEPENDA DEL INTERRUPTOR DE ENCENDIDO / APAGADO COMO EL ÚNICO MEDIO DE DESCONECTAR LA ELECTRICIDAD

CUANDO ESTÉ REPARANDO O TRASLADANDO EL CALEFACTOR. SIEMPRE DESCONECTE EL CABLE ELÉCTRICO. SIEMPRE APAGUE

Y DESCONECTE EL CALEFACTOR ANTES DE DEJAR EL ÁREA. NUNCA DEJE NIÑOS SIN ATENCIÓN CUANDO EL CALEFACTOR

ESTÉ ENCENDIDO O CONECTADO.

Advertising