Panasonic FP0 Series - Manual (Page 26)

FP0 Series
Power Supplies
■ Incredibly small size:
- FP0 power supply: 90 x 60 x 30.4mm
- FP power supply: 115 x 75 x 42mm
■ Maximum output current:
- FP0 power supply: 0.7A (24VDC)
- FP power supply: 2.1A (24VDC)
■ Multiple voltage input:
85 to 265VAC
■ Optimal protection:
overvoltage, overcurrent,
overheating, etc.
■ Global approvals
(UL / cUL, EN, CE-marking)
■ DIN-rail mounting
(FP0 power supply also side
mounting)
Primary side:
Rated operating voltage
Operating voltage range
Rated operating frequency
Operating frequency range
Inrush current
Current consumption
Over voltage protection
Secondary side:
Rated output voltage
Output voltage range
Nominal output current
Output current range
Output ripple
Short circuit protected
Over voltage protected
Over load protected
Holding time
115 / 230VAC
85 to 265VAC
50 / 60Hz
40 to 70Hz
< 50A at 55°C < 50A at 25°C / < 70A at 55°C
145mA (at 230VAC and 0.7A output current)
PROTECTED
24VDC
23.5V to 24.5VDC
0.7A
0 to 0.7A
< 60mVpp
electronic, automatic restart mode
Yes
Yes (switch off at approx. 0.8A and more)
min. 20ms at 230VAC
Order number: FP0-PSA2 FP-PS24-050E
400mA (at 230VAC and 2.1A output current)
2.1A
0 to 2.1A
< 240mVpp
continuous
Yes (switch off at approx. 3.5A and more)
min. 110ms at 230VAC
Power OK signal – Yes
Performance specifications
Ambient temperature
Storage temperature
Ambient humidity
Storage humidity
Vibration resistance
Shock resistance
Life time min.
Mounting
Size
Input connection AC side
Output connection DC side
Status display
0°C to +55°C
-20 °C to +70 °C
5 to 95% non-condensing
5 to 95% non-condensing
10 to 55Hz, 1 cycle/min.: double amplitude of 0.75mm, 10 min. on 3 axes
10g min., 4 times on 3 axes
7 years at nom. load, 25°C ambient temperature,
20000 h at 55°C with full load/continuous operation
DIN rail or FP0 flat attachement plate
90 x 60 x 30.4mm
MC connector, 2 pin
MC connector, 6 pin, 3 pin for „+“ and 3 pin for „-“
DIN rail
115 x 75 x 42mm
2 pin
5 pin, 2 pin for „+” and 2 pin for „-”; 1 pin Power OK
LED (green) at the front side for the secondary voltage indication
General specifications
EMC
LVD
Others
Protection
EN 50082-2, EN50082-1,
EN 50081-2, EN 50081-1 EN 55011/B, EN 55022/B,
EN 61000-4-2, -4-3, -4-4, -4-5, -4-6, -4-11
EN 60950, EN 50178
(overvoltage category 3)
EN 60950, EN 50178
(overvoltage category 2)
UL Recognized according to UL 508, UL 1950,
cUL Recognized according to CAN/CSA-C22.2 No. 950.95
IP30 IP20 outside / IP67 inside
Standards
NOTE:
1) Mounting distance between the FP0 pow-
er supply and the FP0 CPU is needed to
permit heat radiation for the FP0-CPU
2) For side mounting, 2 additional
blue clips are needed: order part-no.
677-021-17101 (1pce.) for FP0-PSA2
3) Mounting distance between the power
supply FP-PS24-050E and other devices is
needed for cooling / heat radiation.
FP0 Power supply
FP0-PSA2
FP Power supply
FP-PS24-050 E
➝
➝
30.4mm
➝
90mm
➝
➝
➝
42mm
➝
115mm
➝
Features
FP0_broschüre_4093 euen0904 15.10.2004 8:44 Uhr Seite 26
Phone: 800.894.0412 - Fax: 888.723.4773 - Web: www.ctiautomation.net - Email: [email protected]