Pioneer Elite VSX-90TXV - Manual (Page 26)

Controls and displays 04
26
En
7 TV CONTROL buttons
These buttons are dedicated to control the TV assigned to
the
TV CTRL button. Thus if you only have one TV to hook
up to this system assign it to the TV CTRL input source
button. If you have two TVs, assign the main TV to the TV
CTRL button (see page 61 for more on this).
TV  – Use to turn on/off the power of the TV.
TV VOL +/– – Use to adjust the volume on your TV.
INPUT SELECT – Use to select the TV input signal.
TV CH +/– – Use to select channels.
8 Component control buttons
The main buttons ( , , etc.) are used to control a
component after you have selected it using the input
source buttons.
The controls above these buttons can be accessed after
you have selected the corresponding input source button
(for example
DVD, DVR1 or TV). The following controls
can be accessed when listening to the built-in tuner:
MPX – Switches between stereo and mono reception
of FM broadcasts. If the signal is weak then switching
to mono will improve the sound quality (page 33).
DISP – Switches between named station presets and
radio frequencies (page 34).
9 Receiver controls
THX – Press to select a Home THX listening mode
(page 28).
STANDARD – Press for Standard decoding and to
switch between the various
2 Pro Logic IIx and
Neo:6 options (page 27).
ADV.SURR – Use to switch between the various
surround modes
(page 28).
STEREO/F.S.SURR – Switches between the stereo
playback mode (page 29) and the Front Stage
Surround Advance mode (page 29).
AUTO SURR – Press to select the Auto Surround
mode (page 27) or the Stream Direct mode (page 30).
Stream Direct playback bypasses the tone controls
and any other signal processing for the most
accurate reproduction of a source (page 30).
ACOUSTIC EQ – Press to select an Acoustic
Calibration EQ setting (page 30).
SIGNAL SEL – Use to select an input signal (page 30).
10 MULTI OPE
Use this button to perform multi operations (page 62).
11 SHIFT
Press to access the controls outlined in white boxes (for
example,
INPUT SELECT ), or to display the currently
selected input source in the remote control LCD.
12 SOURCE 
Press to turn on/off other components connected to the
receiver (see page 61 for more on this).
13 Character display (LCD)
This display shows information when transmitting
control signals.
The following commands are shown when you’re setting
the remote to control other components (see
Controlling
the rest of your system on page 61):
SETUP – Indicates the setup mode, from which you
choose the options below.
PRESET – See Selecting preset codes directly on
page 61.
MULTI OP – See Multi Operation and System Off on
page 62.
SYS OFF – See Multi Operation and System Off on
page 62.
DIRECT F – See Direct function on page 61.
RESET – See Resetting the remote control presets on
page 61.
READ ID – See Confirming preset codes on page 61.
14 RECEIVER
Switches the remote to control the receiver (used to
select the green commands above the number buttons
(
ANALOG ATT, etc.)). Also use this button to set up
surround sound (page 8, page 35). With SHIFT, this
selects the MULTI-ZONE control (page 50).
15 VOL +/–
Use to set the listening volume.
16 MUTE
Mutes the sound or restores the sound if it has been
muted (adjusting the volume also restores the sound).
17 EFFECT/CH SEL and LEVEL +/–
Press repeatedly to select a channel, then use +/– to
adjust the level (see Tip on page 41). Also adjusts the
level of the Advanced Surround effects, the Dolby Pro
Logic IIx Music and Neo:6 Music parameters and the
sound delay setting (page 29). You can then use the
+/– buttons to make these adjustments.
VSX-90TXV_KU.book Page 26 Friday, March 16, 2007 5:46 PM