Panasonic DMR-EX77 - Manual (Page 30)

30
RQT8859
Timer recording
See also “Important notes for recording” ( ➡ 8).
Depending on the type of disc used for recording or the type of
broadcast, there may be restrictions on the title you are trying to
record.
[HDD] [RAM] [-R] [-RW‹V›] [+R] [+RW]
≥You can enter up to 32 programmes up to a month in advance.
(Each daily or weekly programme is counted as one programme.)
[RAM] [-RW‹V›] [+R] [+R]DL] [+RW]
≥To use a new disc, formatting is necessary.
Preparation
≥Turn on the television and select the appropriate video input to suit
the connections to this unit.
≥If recording to DVD, insert a disc that you can use for recording
( ➡ 24).
≥Make sure that the clock settings are correct ( ➡ 73).
Entering G- CODE numbers is an easy way of timer recording. You can
find these numbers in TV listings in newspapers and magazines.
[Note]
The G-
CODE system is not supported for digital broadcasts.
1
Press [G-Code].
2
Press the numbered buttons to enter
the G-
CODE number.
Press [ 2] to move back to correct a digit.
3
Press [OK].
≥Confirm the programme (start and end time) by using a TV
magazine, etc. and make corrections if necessary using
[
3, 4, 2, 1] ( ➡ 31, step 3).
≥When “-- ---” appears in the “Name” column, you cannot set
timer recording. Press [ 3, 4] to select desired programme
position. After you have entered the information of a TV
station, it is kept in the unit’s memory.
4
Press [OK].
The timer programme is stored and the timer icon is
displayed.
“ F” lights on the unit’s display to indicate timer recording
standby has been activated.
Repeat steps 1–4 to programme other recordings.
Press [
Í DVD] to turn the unit off.
∫ To cancel recording when recording has already
begun ( ➡ 32)
∫ To release the unit from recording standby
( ➡ 32)
∫ Notes on timer recording ( ➡ 32)
G- CODE is a registered trademark of
Gemstar Development Corporation. The
G-
CODE system is manufactured under
license from Gemstar Development
Corporation.
STATUS
REC MODE REC
MANUAL SKIP
CREATE
CHAPTER
FU
NC
TIO
N M
EN
U DI
RE
CT
N
AV
IG AT OR
GUIDE
RETURN
PLAY/x1.3 PAUSE STOP
SLOW/SEARCH SKIP
CH
PAGE
SELECT
INPUT 0
9 8 7
6 5 4
3 2 1
CH
AV
Í
TV
DRIVE
SELECT
Í
DVD
VOL
DELETE
EXIT
OK
OPTION
ANALOGUE
CH
G-Code
AUDIO DISPLAY
TIME SLIP PROG/CHECK
G-Code
3,4,2,1
OK
DRIVE
SELECT
REC MODE
Í DVD
PROG/CHECK
Numbered
buttons
“Blue”
Using G- CODE system to make timer
recordings
G-Code
Record 1:58 SP DVD 30:24 SP HDD Remain
12:53:00 15. 7. TUE
Input G-Code Number 0-9, and press OK.
G-Code
Record 1:58 SP DVD 30:24 SP HDD Remain
12:53:00 15. 7. TUE
Input G-Code Number 0-9, and press OK.
Timer
Recording
1:58 SP DVD 30:24 SP HDD Remain
12:54:00 15. 7. TUE
Mode Stop Start Name Date
HDD
DVD
20:00 19:00 15. 7. TUE SP HDD 2A ARD
Programme Name
All Services : ARD
No. Name
ARD 01
&
Timer icon
12:56:00 15. 7. TUE
Mode Stop
HDD
DVD
HDD
Drive
space
SP OK 20:00
Programme
Check to make sure “OK”
is displayed (
➡ 33).
EX77_87GN.book Page 30 Wednesday, May 30, 2007 1:10 PM