Panasonic SC-AK450 - Manual (Page 10)

10
RQT8043
RQTV0191
LANG - 5
LANG - 4
FRANÇAIS
DANSK
ENGLISH
Cassette tape – Play and record
The buttons described for “Cassette tape - Play and
record” are mainly for the main unit unless indicated
otherwise.
TAPE
Basic play Basic play
Use normal position tapes.
High position and metal position tapes can be played, but
the unit will not be able to identify the characteristics of
these tapes.
1 Press [ 3, TAPE].
The unit turns on.
If a cassette was loaded, play starts automatically (One
touch play).
2 Press [ 0, OPEN] and insert the cassette.
Insert with the side to be played facing towards you
and the exposed tape facing down. Close the holder by
hand.
3 Press [ 3, TAPE] to start play.
To Action
stop tape playback Press [ 7, STOP].
fast-forward and
rewind Press [ , REW / 4 ] or [ , FF / ¢].
Note:
• Tapes exceeding 100 minutes are thin and can break or get
caught in the mechanism.
• Tape slack can get caught up in the mechanism and should be
wound up before the tape is played.
TPS (Tape Program Sensor) TPS (Tape Program Sensor)
This function enables you to search the beginning of up to
a maximum of 9 tracks.
Press [ , REW / 4] or [ , FF / ¢] during play.
Play resumes from the track found.
Note:
TPS may not operate correctly in the following situations:
• If the interval between tracks is less than 4 seconds.
• If there is noise between tracks.
• If there are silent parts within tracks.
Recording Recording
Selection of tapes for recording
Use normal position tapes.
High position and metal position tapes can be used, but
this unit will not be able to record or erase them correctly.
Preparation
Wind up the source tape so recording can begin
immediately.
1 Press [ 0, OPEN] and insert the cassette to be
recorded.
Insert with the side to be recorded facing towards you
and the exposed tape facing down.
2 Select the source to be recorded.
Radio recording:
Tune in the station. (
\ page 11 ~ 13)
Disc recording:
1 Insert the disc(s) you want to record.
Press [ 6, CD] and then [7, STOP].
2 Prepare the desired disc recording mode.
To Action
record
programmed
tracks
Perform steps 2 to 4 in “Program play”
(
\ page 8).
Perform steps 3 to 6 in “Program play”
(
\ page 8).
By remote control only
record
specifi c
discs/tracks
1) Press [DISC] and then [1] ~ [5] to select
the disc.
Ensure disc is stopped.
2) Press [PLAY MODE] to select the desired
mode ( \ page 7).
3)
For 1-ALBUM mode and 1-TRACK mode:
Press [ALBUM ( or )] to select the
album.
For 1-TRACK mode:
Press [ 4, REW/ ] or [¢, / FF] to
select the track.
3 Press [ ¶, REC] to start recording.
Other basic operations Other basic operations
To Action
stop recording Press [ 7, STOP].
record on the other
side of the tape Turn the cassette over and press [ ¶, REC].
erase a recorded
sound 1) Press [ 3, TAPE] and then [7, STOP].
2) Insert the recorded cassette.
3) Press [
¶, REC].
Note:
Changes to volume and sound adjustments quality do not affect
recording.
Erasure prevention Erasure prevention
The illustration shows how to remove the tabs to prevent
recording. To record on the tape again, cover as shown.
Side A
Tab for side A Tab for side B
To re-record
Normal cassette
Adhesive tape
RQTV0191-P_1EN.indd 10 RQTV0191-P_1EN.indd 10 2/16/07 10:25:46 AM 2/16/07 10:25:46 AM