Panasonic SCAK75 User Manual
Cd stereo system
Attention! The text in this document has been recognized automatically. To view the original document, you can use the "Original mode".
Advertising
Table of contents
Document Outline
- RQT4220-1P
- ■ filili ttttllitlfell
- i
- i
- s
- Press TUNER BAND to select the band.
- n Press TUNE MODE to select “MANUAL”.
- Press V or A until the display shows the frequency from which you want to begin automatic memory presetting.
- Fj Press and hold MEMORY until the frequency begins to change.
- n Pt'ess TUNER BAND to select band.
- n Press TUNE MODE to select “PRESET” or “MANUAL”.
- B Press V or A to select the desired broadcast.
- Adjust the volume level.
- s
- g
- &
- Q
- Q Press DISC/TRACK to select the CD selection mode.
- 0 Turn JOG to select the desired CD number.
- Press DISC/TRACK to select the track selection mode.
- Turn JOG to select the desired track number.
- El
- Press OPEN to open the rack panel, and set the CD in slot No. 0.
- Close the rack panel and press SINGLE >,
- &
- 8
- □
- □
- n Press CD.
- Press PROGRAM.
- Press DISC.
- Select the CD(s) you want with the numeric button(s).
- Press the numeric button(s) to select the desired track.
- Repeat steps 3 through 5 until you have programmed ail the tracks you want.
- Press PROGRAM.
- о О О
- s
- &
- 8
- To replay your program
- If you program a track not on your CDs
- Press CD,
- Q Press CD MANAGER to select the desired mode.
- Ql Press DISC/TRACK to select the CD selection mode.
- pj Turn JOG to select the desired CD number.
- Q Press DISC/TRACK to select the track selection mode.
- Turn JOG to select the desired track number.
- Press /11/A.
- Press TEXT MODE.
- s
- i
- i
- Press
- 5
- 6
- 8
- g
- □
- Press the SOUND EQ joystick to turn on the equalizer.
- Dial SOUND EQ to select the sound quality or sound field.
- Press SUPER.WOOFER.
- s
- &
- Press the SOUND EQ joystick to turn on the equalizer.
- Dial SOUND EQ to display “Al EQ”.
- operate the SOUND EQ joystick and set the sound quality as desired.
- Press the SOUND EQ joystick to turn on the equalizer.
- Dial SOUND EQ to display “MANUAL”.
- Operate the SOUND EQ joystick and set the sound quality as desired.
- &
- &
- s
- B
- Press VOLUME (—) or {+) to set the volume level normally used for enjoying the source.
- Press CH SELECT to select the center or surround speakers.
- Press CH LEVEL (—) or (+) to adjust the output level.
- Press DOLBY PRO LOGIC to turn on the DOLBY PRO LOGIC system.
- Select and start the desired source.
- Disconnect the microphone(s).
- Press TAPE.
- Q Insert the recorded tape into deck 2.
- Q Press REV MODE to select reverse mode.
- B Press • REC/STOP.
- n Press DECK 2 ^ OPEN and Insert the tape.
- Press REV MODE to select the reverse mode.
- Select a radio station.
- PI Press • REC/STOP to start recording.
- s
- 0
- 0
- □
- □
- Q
- El
- Before recording
- Press CD.
- Q Press CD MANAGER to select the desired
- mode.
- Q Press DISC/TRACK to select the CD selection
- mode.
- 3 Turn JOG to select the desired CD number.
- Press DISC/TRACK to select the track selection mode.
- B Turn JOG to select the desired track number.
- Press • REC/STOP to start recording.
- Press TAPE.
- B Press ^ OPEN on both decks and insert the tapes.
- PI Press REV 1VIODE to select the reverse mode.
- □ Press TAPE EDIT to start recording.
- vO
- n First, lower volume with MIC VOL, connect the microphone(s).
- Press KARAOKE to select the voice mode.
- Start the source (CD, etc.).
- y Adjust volume with VOLUME and MIC VOL and sing along.
- fl First, lower volume with WlIC VOL then, connect the microphone(s).
- Q Press DECK 2 ^ OPEN to insert the tape and then select the reverse mode.
- Q Press KARAOKE to select the voice mode.
- p] Start recording and KARAOKE performance.
- H Press CLOCK/TIMER to select ‘© PLAY”.
- © Press V or A to select the starting time. © Press CLOCK/TIMER.
- © Press V or A to select the ending time. ©Press CLOCK/TIMER.
- Select the desired source and then prepare for playing.
- Set the playback volume, g Press © PLAY/© REC to select “® PLAY”.
- (/slft0 file t/mer
- H Press CLOCK/TIMER to select “© REC”.
- ® Press V or A to select the starting time. ® Press CLOCK/TIMER.
- © Press V or A to select the ending time. (2) Press CLOCK/TIMER.
- Select the desired source and then prepare for recording.
- B Prepare for recording.
- g Press © PLAY/0 REC to select “© REC”.
- Press SLEEP to select the desired time.
- a:
- (^DS® (Sdí®
- El
- Q