Panasonic DMP-BD45 - Manual (Page 13)

13
VQT2H86
C
o
nn
e
c
ti
o
ns
&
Se
tt
in
g
s
Access Point Connection Setting
Network Easy Setting (Connection Check)
Network Easy Setting (Internet Connection Check)
≥ Refer to the operating instructions of the hub or router.
≥ You can perform this setup anytime by selecting “Network Easy Setting” in
the Setup menu. ( > 28)
≥ You can redo these settings individually using “Network Settings”. ( > 28)
≥ Do not use this device to connect to any wireless network for which you
do not have usage rights.
During automatic searches in a wireless network environment, wireless
networks (SSID*) for which you do not have usage rights may be
displayed; however, using these networks may be regarded as illegal
access.
≥ After performing network settings on this unit, the settings (encryption
level, etc.) of the Wireless router (Access point) might change. When you
have trouble getting online on your PC, perform the network settings on
your PC in accordance with the settings of Wireless router (Access point).
* An SSID (Service Set IDentification) is a name used by wireless LAN to
identify a particular network. Transmission is possible if the SSID
matches for both devices.
When you experience
problems with settings
Display Check the following
A conflict with another
device occurred. ≥ Please wait a few moments,
and then try again.
A time out error occurred.
≥ Setting of the Wireless
router (Access point) for
MAC Address etc.
≥ The signal may be weak.
Using the USB extension
cable included with the
Wireless LAN Adaptor,
adjust the position of the
Wireless LAN Adaptor.
≥ The SSID* and the
encryption key of the
Wireless router (Access
point).
≥ Please wait a few moments,
and then try again.
An authentication error or a
time out error occurred.
A device error occurred.
≥ Connection of Wireless LAN
Adaptor
If there is no improvement in
symptom, contact our
Customer Service Center.
Display
Check the
following
1. LAN cable connection or
Connection to access point
: Fail
≥ Connection of
the LAN
cables (> 10)
2. IP address setting : Fail
3. Connection to gateway : Fail
OK
Access Point Connection Setting
Failed to connect to the access point.
A conflict with another device occurred.
Do you want to configure Access Point Connection
Setting again ?
Yes No
OK
Network Easy Setting (Connection Check)
Yes No
Complete.
1. LAN cable connection
2. IP address setting
3. Connection to gateway
LAN cable is not connected.
Please check the connection.
Select “Yes” and press [OK] to check network
connection again. Select “No” and press [OK]
to finish Network Easy Setting.
: Fail
: Fail
: Fail
1. LAN cable connection or
Connection to access point
: Pass
≥ Connection
and settings
of the hub
and router
≥ Settings of
“IP Address/
DNS
Settings”
(> 28)
2. IP address setting : Fail
3. Connection to gateway : Fail
1. LAN cable connection or
Connection to access point
: Pass
2. IP address setting : Pass
3. Connection to gateway : Fail
Display Check the following
Cannot find the server.
(Error code: B019)
≥ “Primary DNS” and “Secondary
DNS” settings of “IP Address/
DNS Settings” (> 28)
Failed to connect to
the server.
(Error code: B020)
≥ The server may be busy or the
service may have been
suspended. Please wait a few
moments, and then try again.
≥ Settings of “Proxy Server
Settings” (> 28) and the router
OK
Network Easy Setting (Internet Connection Check)
Complete.
- Connection to the Internet : Fail(Error code: B019)
Failed the connection test.
Cannot find the server.(Error code: B019)
Please refer to the operating instructions for the cause
of the error and the solution for it.
Press [OK].
VQT2H86~Body_eng.fm 13 ページ ２０１０年１月１８日 月曜日 午前１０時２１分