Panasonic AJ-SD965P - Manual (Page 56)

56
Setup menus
(continued)
The underlined items indicates the initial setting.
USER menu <AUDIO>
No./Item Description No./Item Description
721
MONI CH SEL
This selects the monitor output.
0000 MANU :
The output signal is as selected in MONITOR
SELECT buttons.
0001 AUTO :
PCM AUDIO output is selected within the
–0.43 (–0.5)a to +1a speed range; CUE is
automatically selected for all other tape
speeds.
<Note>
The value for the DV/DVCAM tape is shown in
parenthesis ( ).
0002 PCM :
The PCM AUDIO signal is output over the
–10a to +10a range.
<Note>
This setup menu’s setting takes effect when
CH1, CH2, CH3 or CH4 has been selected by
the L and R MONITOR SELECT buttons on the
front panel. (If CUE has been selected, the cue
signal will be output at all the speeds regardless
of the setup menu’s setting.)
726
REC CUE
This selects the input signal recorded in
CUE.
0001 CH1 : Audio CH1 input
0002 CH2 : Audio CH2 input
0003 CH1+2 : Audio CH1 and CH2 MIX signal
0004 CH3 : Audio CH3 input
0005 CH4 : Audio CH4 input
0006 CH3+4 : Audio CH3 and CH4 MIX signal
0007 CH1~4 : Audio CH1, CH2, CH3 and CH4
mixed signals
727
PB FADE
This selects the processing method for the
audio edit points (IN point, OUT point) during
playback.
0000 AUTO : According to the status during
recording.
0001 CUT : Forced CUT
0002 FADE : Forced FADE
728
EMBEDDED
AUD
This selects whether to superimpose the
audio data onto the SDI output.
0000 OFF : Data is not superimposed.
0001 ON : Data is superimposed.
731
CUE OUT SEL
This selects whether or not the cue signal is
to be output to the main line output in the
search mode.
0000 OFF : CUE is not output.
0001 ON : CUE is output.
<Notes>
O This function works only when a setting
other than MANU has been selected by
setup menu No. 721 (MONI CH SEL).
O The main signal system output channels
used for the CUE output differ depending
on the setting selected by setup menu No.
735 (MON AUTO SEL).
When L/R is selected:
CUE is output to CH1 to CH4.
When L is selected:
CUE is output to CH1 and CH3.
When R is selected:
CUE is output to CH2 and CH4.
O When PCM has been selected as the setup
menu No. 721 (MONI CH SEL) setting,
PCM is output.
733
CUE OUT
This selects the timing for the output picture
and CUE output when CUE has been
selected for monitor output.
0000 NORMAL : The timing is aligned with the
output picture.
0001 DIRECT : Whatever has been recorded on
the tape is output with no delay.
<Note>
When DIRECT has been selected, the timing of
the output picture and that of the cue output are
not aligned properly.
735
MON AUTO
SEL
Although CUE is automatically output to the
monitor output in accordance with the
operation mode when a setting AUTO has
been selected by setup menu item No. 721
(MONI CH SEL), the MON AUTO SEL setup
menu item is used to select the monitor
channel which is to be automatically
switched to CUE.
0000 L/R :
CUE is output to both the left and right
channels.
0001 L :
CUE is output to the left channel only.
0002 R :
CUE is output to the right channel only.
734
MONI SEL INH
This selects whether the operation of the
AUDIO MON SEL button on the front panel is
to be enabled or disabled.
0000 OFF : Operation is enabled.
0001 ON : Operation is disabled.
0002 ON1 :
Operation is disabled in the FULL display
mode and enabled only in the FINE display
mode.