Panasonic PT-AE700U - Manual (Page 24)

E NGLISH -47
Adjustments
and
settings
46-E NGLISH
Option settings
Press the F or G button to select
an item, and then press the I or H
button to change the setting.
OSD
ON
The signal name is displayed in the
top-right corner of the screen when
the input signal is changed.
OFF
Use this setting when you do not
want the signal name to be
displayed.
Noise Reduction (NR)
If the signal is of such poor quality
that picture interference appears,
set “NR” to “ON”. To turn off the
“NR” feature, set to “OFF”.
O P T I O N
O S D O N
N R O N
C I N E M A R E A L I T Y O N
B A C K C O L O R B L U E
W S S O N
F R O N T / R E A R F R O N T
D E S K / C E I L I N G D E S K
F A N C O N T R O L N O R M A L
L A M P P O W E R H I G H
L A M P R U N T I M E 5 H
S E L E C T A D J E S C
CINEMA REALITY
[S-VIDEO/VIDEO/PC/HDMI/525i
(480i), 625i(576i), 1 125(1 080)/60i
and 1 125(1 080)/50i YP
B P R only]
ON
Set to “ON” when you would like 24
frames per second pictures (such as
movies) to project the source
faithfully.
OFF
Set to “OFF” when the projected
pictures have problems with
captions or subtitles when the
setting is “ON”.
BACK COLOR
This sets the color which is
projected onto the screen when no
signal is being input to the projector.
WSS
ON
When WSS (Wide Screen
Signalling) is detected from PAL or
625i(576i) YP
B P R signals, the
aspect ratio will also be switched
automatically.
OFF
WSS will not be detected from PAL
or 625i(576i) YP
B P R signals.
O S D O N
[
O F F
N R O N
[
O F F
B A C K C O L O R B L U E
[
B L A C K
C I N E M A R E A L I T Y O N
[
O F F
FRONT/REAR
This setting should be changed in
accordance with the projector
setting-up method. (Refer to page 16.)
FRONT
When the projector is placed in front
of a screen.
REAR
When using a translucent screen.
DESK/CEILING
This setting should be changed in
accordance with the projector
setting-up method. (Refer to page 16.)
DESK
When the projector is placed on a
desk or similar.
CEILING
When the projector is suspended
from a ceiling using the ceiling
bracket (sold separately).
FAN CONTROL
Set “FAN CONTROL” to “HIGH”,
when using this projector at high
elevations (above 1 400 m) only.
LAMP POWER
This setting changes the lamp
brightness. When set to “LOW”, the
luminance of the lamp is reduced,
but the projector uses less power,
and the operating noise is also
reduced.
The “LOW” setting is recommended
for narrow rooms where a high
picture luminance is not essential or
for watching movies.
LAMP RUNTIME
This setting displays the usage time
for the lamp unit which is currently
being used. When replacing the
lamp unit, follow the instructions on
page 52, and reset “LAMP
RUNTIME” to “0”.
D E S K / C E I L I N G D E S K
[
C E I L I N G
L A M P P O W E R H I G H
[
L O W
F R O N T / R E A R F R O N T
[
R E A R
NOTE:
B The lamp’s operating life varies
depending on the usage
conditions (such as the “LAMP
POWER” setting and the
number of times the power is
turned on and off).
W S S O N
[
O F F
NOTE:
B “LAMP POWER” cannot be set
when no signal is being input.
NOTE:
B The setting for “TV-SYSTEM”
will also be displayed when an
S-VIDEO/VIDEO signal is being
input.
NOTE:
B “NR” cannot be set when HDMI
signals are being input.
F A N C O N T R O L N O R M A L
[
H I G H