Pioneer VSX-21 - Manual (Page 25)

25
<ARB7181>
SET UP
OPERA
TION
Remote Control
These pages describe the buttons on the remote control
used to operate the receiver.
7 Number buttons
These buttons can perform a variety of different
functions depending on the remote operation mode.
• [RECEIVER operations (press RECEIVER first)]
: Press repeatedly to select the standard Dolby/
DTS mode and the ADVANCED THEATER modes.
(Refer to page 30, 32)
DSP MODE : Press repeatedly to select a DSP sound
mode (refer to page 31).
MIDNIGHT : Press to hear surround sound effectively
at low volumes (refer to page 35).
CH.SELECT : Use to select a speaker when adjusting
speaker levels.
TEST TONE : Press to switch the test tone on or off
when listening to a surround mode (refer to page 21).
ATT : Press to attenuate (lower) the level of the input
signals and prevent distortion (refer to “Display”, 5,
Overload indicator on page 24).
SIG.SELECT : When the same component uses both
analog and digital connections, use to select input
signals as digital or analog.
CH.LEVEL (–/+) : Use to adjust individual speaker levels.
EFFECT (+/–) : Use to adjust the DSP mode effect level.
• [TUNER operations (press TUNER first)]
Number buttons (0~9) : During preset tuning, use to
input the number of the preset station. Use to input
the station frequency during direct tuning.
CLASS (+10) : Press repeatedly to switch the preset
station classes during preset tuning.
MENU : Press to activate direct tuning.
8 FUNCTION button
Press repeatedly to select a source.
9 MODE CHECK button
Press to confirm the current remote operation mode
and to switch operation modes without changing the
source (refer to page 51).
0 Power button
Press to turn on or put in standby all connected
components other than this unit.
- TV/TV FUNC button
Press TV to turn the TV’s power on or put in standby.
Press TV FUNC to select the TV for remote control
operation.
= RECEIVER button
Press to select the receiver for remote control
operation.
~ FL DIMMER button
Press to adjust the brightness of the fluorescent
display. Four levels of brightness ranging from very
dim to very bright can be selected.
! COMMANDER SET UP button
Use to customize the remote control functions.
(Refer to “Setting Up the Remote Control” starting on
page 22.)
@ DIRECT button
Use to playback original source audio. When DIRECT
is ON, Dolby, DSP, LOUDNESS, DIGITAL NR and
MIDNIGHT mode are automatically turned OFF.
DVD/LD
VCR 1
TV/SAT CD
TUNER
VCR 2 MD/TAPE
TV CONTROL
RECEIVER
DSP MODE
CH.SELECT ATT SIG.SELECT
MIDNIGHT
TEST TONE
AUDIO/VIDEO PRE-PROGRAMMED
REMOTE CONTROL UNIT
2 3
5
0
6
9 +10
TV/VCR CLASS
7 8
4 1
CHANNEL
MULTI CONTROL
ENTER
VOL VOL
FQ
FQ
+
–
TV FUNC
RECEIVER TV
MUTING
CN.LEVEL EFFECT
FL DIMMER FUNCTION DIRECT
MODE CHECK
COMMANDER
SET UP
Î
MEMU
1
2
3
4
5
6
7
8
9
0
-
=
~
!
@
1 RECEIVER button
Press to switch the receiver on or to put in standby.
2 MUTING button
Press to mute the volume. “MUTING” appears in the
display. Press again to cancel.
3 %˜fi˜@˜#˜ENTER buttons
Specific use of these buttons is described in
conjunction with the operations they are used in.
ENTER : Press to switch the band (FM/AM) when
using the tuner.
4 VOL (+/–) buttons
Press to adjust the volume. When VOL (+/–) buttons
are pressed while muting, muting is canceled.
5 CHANNEL (+/–) button
Use to select preset stations when operating the
tuner. When the remote is used to control other
components, this button may be used to change
channels, tracks, or chapters.
6 MULTI CONTROL buttons
Use these buttons to select the remote operation
mode.
For example, pressing TUNER sets the remote to
operate the tuner functions.
Names of Parts and Basic Operations