Panasonic DMR-E95H User Manual
Page 57
57
RQT7392
Ref
e
rence
Sound
Page
Operation
Recording/Timer recording/Transferring (dubbing)
Continued on next page
No sound.
Low volume.
Distorted sound.
Cannot hear the desired audio
type.
≥
Check the connections and settings. Check the input mode on the amplifier if you have
connected one.
≥
Press [AUDIO] to select the audio.
≥
Turn off V.S.S. in the following cases.
–When using discs that do not have surround sound effects such as Karaoke discs.
–When playing MTS broadcast programs.
≥
The disc may have a restriction on the method of audio output. If “D.MIX” does not appear in
the display when playing multi-channel DVD-Audio, only audio for the two front channels will
be output. Refer to the disc’s jacket.
[DVD-A]
7–9, 49
17, 26
31
—
Cannot switch audio.
≥
You cannot switch the audio in the following cases.
–When a DVD-R disc is in the disc tray while DVD drive is selected.
–When the recording mode is XP and “Audio for XP Recording” is set to “LPCM”.
–When “DVD-R High-Speed Recording” is set to “On”
≥
You have used digital connection. Set “Dolby Digital” to “PCM” or connect using audio cables
(analog connection).
≥
There are discs for which audio cannot be changed because of how the disc was created.
—
49
48
49, 9
—
Cannot operate the television.
The remote control doesn’t
work.
≥
Change manufacturer code. Some televisions cannot be operated even if you change the
code.
≥
The remote control and main unit are using different codes. Change the code on the remote
control.
Press and hold [ENTER] and the indicated number button at
the same time for more than 2 seconds.
≥
The batteries are depleted. Replace them with new ones.
≥
Colored glass may obstruct the signal reception/transmission.
≥
Don’t place the signal sensor in direct sunlight or in areas that may be subject to sunlight
exposure.
12
13
4
—
—
The unit is on but cannot be
operated.
≥
Recording drive or playback drive has not been selected properly.
≥
Some operations may be prohibited by the disc.
≥
The unit is hot (“U14” appears on the display). Wait for “U14” to disappear.
≥
One of the unit’s safety devices may have been activated.
Reset the unit as follows:
Press [POWER
Í
/I] on the main unit to switch the unit to standby.
If the unit doesn’t switch to standby, press and hold [POWER
Í
/I] on the main unit for about
10 seconds. The unit is forcibly switched to standby.
Alternatively, disconnect the AC power supply cord, wait one minute, then reconnect it.
16, 24
—
—
—
HDD activation is slow.
≥
The HDD is in SLEEP mode. (“HDD SLP” appears in the unit’s display.)
60
Cannot eject disc.
≥
The unit may have a problem. While the unit is off, press and hold [
∫
] and [CH
W
] on the
main unit at the same time for about 5 seconds. Remove the disc and consult the dealer.
—
Cannot record.
≥
You haven’t inserted a disc or the disc you inserted cannot be recorded on. Insert a disc the
unit can record onto.
≥
The disc is unformatted. Format the disc.
[RAM]
≥
The write-protect tab on the cartridge is set to PROTECT, or the disc is protected with DISC
SETTING.
≥
Some programs have limitations on the number of times they can be recorded. (CPRM)
≥
You cannot record when there is not enough space or when the number of titles has reached
its limit. Erase unwanted titles.
≥
You cannot record on finalized DVD-R discs.
≥
Due to peculiarities of DVD-R, you may be unable to record onto them if you either insert and
remove the disc or switch the unit on and off while a disc is loaded, a total of fifty times.
≥
A DVD-R recorded on this unit may not be recordable on other Panasonic DVD recorders.
14
45
44
53
26, 33,
44, 45
—
—
—
Timer recording does not work
properly.
VCR Plus
r
system does not
work properly.
≥
The timer program is incorrect or different timer program times overlap. Correct the program.
≥
Timer recording program may be deleted if there is an interruption to the power.
≥
VCR Plus
r
system works only after this unit downloads the television program list.
22
—
—
Timer recording does not stop
even when [
∫
] is pressed.
≥
Press [
∫
] and then [ENTER] within 5 seconds. Recording stops.
19, 20,
21
The timer program remains
even after recording finishes.
≥
The timer program remains unless set to “Once”.
19, 20
A part or whole of a recorded
title has been lost.
≥
If there is a power failure or the plug is disconnected from the household AC outlet while
recording or editing, the title may be lost or the HDD/disc may become unusable.
You will have to format the disc (
[HDD]
[RAM]
) or use a new disc. We cannot offer any
guarantee regarding lost titles or discs.
45
7392en.book 57 ページ ２００４年４月２７日 火曜日 午後５時３０分