Functional overview, Front panel rear panel, 11 en – Philips HTS3251B/F7 User Manual
Page 11: Front panel, Rear panel
11
EN
EN
FUNCTIONAL OVERVIEW
* The unit can also be turned on by pressing these buttons.
1.
Q (standby/on) button
• Press to turn on the unit, or to turn the unit into the
standby mode. (To completely turn off the unit, you
must unplug the AC power cord.)
• Press and hold for 10 seconds to shut down the unit.
• This button lights up in red when the unit is in
standby mode and turns off when the power is on.
2.
Disc tray
• Place a disc after opening the disc tray.
3.
A
(open/close) button*
• Press to open or close the disc tray.
4.
H
/ G (previous / next) button
• Press to skip to the previous or next title / chapter /
track.
5.
C
(stop) button
• Press to stop playback.
6.
B
(play) button*
• Press to start or resume playback.
7.
SOURCE button
• Press to switch the active source mode.
8.
Infrared sensor window
• Receive signals from your remote control so that
you can control the unit from a distance.
9.
Display
• Refer to “Front Panel Display” on page 14.
10. VOLUME jog
• Rotate to adjust the volume.
11. SD CARD slot
• Insert an SD Memory Card and play back the
contents in it.
12. MP3 LINK jack
• Phono input for connecting to the headphone jack
on your portable audio player.
1.
AC power cord
• Connect to a standard AC outlet to supply power to
this unit.
• Unplug this cord from the AC outlet to completely
turn off the unit.
2.
5.1ch Audio Out jacks (SPEAKERS (4
Ω))
• Use to connect supplied 5.1ch speakers.
3.
LAN terminal
• Use to connect a telecommunications equipment
with LAN cable.
4.
HDMI OUT jack
• Use to connect to a display with an HDMI
compatible port with an HDMI cable.
5.
AUDIO IN (AUX1 / AUX2) jacks
• Use to connect an other device with audio out jack
with an RCA audio cable.
6.
FM ANT 75
Ω jack
• Use to connect the supplied FM wire antenna.
7.
DIGITAL AUDIO IN (COAXIAL) jack
• Use to connect an other device with a digital audio
coaxial output jack with a digital audio coaxial
cable.
8.
COMPONENT VIDEO OUT jacks
• Use to connect a TV monitor with component video
inputs with an RCA component video cable.
9.
VIDEO OUT jack
• Use to connect a TV monitor, an AV receiver /
amplifier or other device with an RCA video cable.
Front Panel
2
1
5 6*
7 8
10
11
12
3*
4
9
Note
• This unit will be turned into the standby mode
automatically after 25 minutes of no action.
Rear Panel
SUB-
WOOFER
FRONT
CENTER
REAR
FRONT
SPEAKERS 4
AC 120V
60Hz
LAN
HDMI OUT
COMPONENT VIDEO OUT
VIDEO OUT
Y
Pr
Pb
DIGITAL
AUDIO IN
COAXIAL
FM
ANT
75
AUDIO IN
AUX 1
AUX 2
1
9
8
7
4
6
3
2
5
Note
• Do not touch the inner pins of the jacks on the rear
panel. Electrostatic discharge may cause permanent
damage to the unit.
• This unit does not have the RF modulator.
In
tr
od
uct
ion
Con
n
ec
ti
o
n
s
B
as
ic Setup
P
layb
ack
Othe
rs
Fun
ct
ion S
e
tu
p
O
the
r Fu
nc
ti
on
s