Philips TDA8946J - Manual (Page 19)

Philips Semiconductors
TDA8946J
2 x 15 W stereo BTL audio amplifier
Product specification Rev. 02 — 14 March 2000 19 of 23
9397 750 06863 © Philips Electronics N.V. 2000. All rights reserved.
18. Revision history
Table 11: Revision history
Rev Date CPCN Description
02 20000314 - Product specification; second version; supersedes initial version TDA8946J-01 of
14 April 1999 (9397 750 04882). Modifications:
• Table 1 on page 1 : SVRR; Typ value 65 dB
→
added
• Ordering options removed
• Figure 1 on page 2 : Block diagram; pin numbers changed OUT2
− →
14 and OUT2+
→
17
• Figure 2 on page 3 : Pin configuration; pin numbers changed OUT2
− →
14 and OUT2+
→
17
• Table 3 on page 3 : Pin description; pin numbers changed OUT2
− →
14 and OUT2+
→
17
• Section 8 “Functional description” :
– Section 8.1 “Input configuration” on page 4
→
added.
– Section 8.2 “Power amplifier” on page 5 : ........, capable of delivering a peak output
current of 1.5 A
→
changed to 2 A.
– Section 8.2.1 “Output power measurement” on page 5
→
added
– Section 8.2.2 “Headroom” on page 5
→
added
• Section 8.3 “Mode selection” :
– Standby mode: V
MODE
> (V
CC
−
0.5 V)
→
changed to (V
CC
−
0.5 V) < V
MODE
< V
CC
;
The power consumption of the TDA8946J will be reduced to <0.18 mW
→
added.
– Mute mode: the DC level of the input and output pins remain on half the supply
voltage
→
added;
– 2.5 V < V
MODE
< (V
CC
−
1.5 V)
→
changed to 3 V < V
MODE
< (V
CC
−
1.5 V)
– Section 8.3.1 “Switch-on and switch-off” on page 6
→
added
• Section 8.4 “Supply Voltage Ripple Rejection (SVRR)” on page 6
→
added
• Section 8.5 “Built-in protection circuits” on page 6
→
added
• Table 5 on page 7 :
– P
tot
value added 28 W
– V
CC(sc)
value added 15 V
• Table 6 on page 7 :
– R
th(j-a)
value added 40 K/W
– R
th(j-c)
value 10 k/W
→
changed to R
th(j-mb)
value 4.5 K/W;
condition ‘in free air’
→
changed to ‘both channels driven’
• Table 7 on page 7 : V
CC
: Max value 18 V changed to
→
25 V; V
MODE
- mute mode - value
Min 2.5
→
changed to 3 V
• Table 8 on page 8 :
– SVRR; Typ values 65 and 60 dB
→
added
–
α
cs
; Typ value 75 dB
→
added
– R
source
changed to
→
R
S
in table and associated table notes; Value added R
S
= 0
Ω
;
– Table note [2] : .... 100 mV (RMS).... changed to
→
... 700 mV (RMS)....
• Figure 3 to 13 : figures added
• Section 13 “Internal circuitry” on page 13 :
→
added
• Figure 14 : figure modified