Panasonic SCHT56 - Manual (Page 17)

17
RQTX0175
The radio
2 1
The radio
Press [INPUT SELECTOR < or >]
to select “TUNER FM” or “TUNER
AM”. Select the frequency.
Auto tuning starts if you press and
hold the button.
Direct tuning
Input the frequency of the station.
Remote control
1. Press [TUNER, ―BAND] to select “TUNER”.
2. Press and hold [TUNER , ―BAND] to select “TUNER
FM” or “TUNER AM”.
3. Press [TUNER DIRECT TUNING].
4. Press the numbered buttons to enter the
frequency.
e.g. To select 107.9 MHz, press [1] → [0] → [7] → [9]
If you do not press a button while the cursor is flashing, the
display returns to the frequency being received.
If the frequency has not been input correctly, “ERROR” will be
displayed. •
•
Automatic presetting
The FM stations the unit can receive are preset in channels 1 to
30. The AM stations the unit can receive are preset in channels
21 to 30 (FM stations are replaced if any were preset in these
channels).
Preparation: Tune to either FM 87.9 MHz or AM 530 kHz.
Main unit
1. Press [-MENU] to select “TUNER” ➡ “AUTO
MEMO”.
2. Press [TUNE 2 / - or 1 / +] to select “START”
➡ [ENTER].
Select “CANCEL” to cancel.
The tuner presets all the stations it can receive into the channels
in ascending order.
During automatic presetting, the memory indicator (M) flashes
and the frequency scrolls. The memory indicator and channel
numbers are displayed for a second when a station is preset.
The last station to be preset is displayed when presetting
finishes.
1. Press [-MENU] to select “TUNER” ➡ “TUNE
MODE”.
2. Press [TUNE 2 / - or 1 / +] to select “PRESET”
➡ [ENTER].
Select “MANUAL” to cancel.
3. After exiting the menu:
Press [TUNE 2 / - or 1 / +].
Manual presetting
Preset the stations one at a time.
Preparation: Tune to the station you want to preset.
Main unit
1. Press [-MENU] to select “TUNER” ➡ “MEMORY”.
2. Press [TUNE 2 / - or 1 / +] to select the channel
➡ [ENTER].
(“STORED” lights.)
For your reference
FM stations can also be preset in the MONO mode.
Selecting channels
Remote control
1. Press [TUNER, ―BAND] to select “TUNER”.
2. Press [SKIP u, 2 or i, 1 ].
or
Press the numbered buttons.
For channels 1 to 9, press the corresponding number.
For channels 10 or over, press [ ≧10], then the two digits.
e.g. To select channel 21: [ ≧10]
→ [2] → [1]
Main unit
You can improve FM reception by switching reception to
monaural.
Main unit
1. Press [-MENU] to select “TUNER” ➡ “FM MODE”.
2. Press [TUNE 2 / - or 1 / +] to select “MONO”
➡ [ENTER].
Select “AUTO” to cancel.
Reducing excessive noise
During FM stereo reception During AM reception
When there is a lot of noise interference with an AM broadcast,
try switching this mode.
1. Press [-MENU] to select “TUNER” ➡ “BEAT
PROOF”.
2. Press [TUNE 2 / - or 1 / +] to select “MODE 1” or
“MODE 2” ➡ [ENTER].
Main unit
SC-HT56P_MP (RQTX0175-2P).indb 17 9/19/2008 12:28:47 PM