Panasonic SCEN38 - Manual (Page 8)

8
RQTV0288
The SLEEP timer can turn the unit off after a set time.
Press [SLEEP] to turn the SLEEP function on/off.
Each time you press the button:
OFF (Canceled)
g To check the remaining time Press [SLEEP] once
The play timer and sleep timer can be used together. The sleep timer
always has priority. Be sure not to overlap timer settings.
•
You can set the timer to come on at a certain time to wake you up.
Preparation:
Turn the unit on and set the clock.
Prepare the music source (disc, radio, iPod or music port) and set the
volume.
 Press [CLOCK/TIMER] repeatedly to select play timer.
CLOCK z PLAY Original display
 “ON TIME” is displayed. Within 5 seconds, press [u, 2] or
[i, 1] to set the starting time.
 Press [CLOCK/TIMER] to confirm.
 “OFF TIME” is displayed. Repeat steps 2 and 3 to set the finishing
time.
To activate the timer

Press [zPLAY] to turn on the timer.
 Press [^] to turn off the unit.
To Action
Change the settings Repeat steps 1 to 4 and 6.
Change the source or
volume  Press [zPLAY] to clear zPLAY indicator
from the display.
 Make changes to the source or volume.
 Perform steps 5 and 6.
Check the settings
(when the unit is on or
in standby mode) Press [CLOCK/TIMER] repeatedly to select
z PLAY.
Cancel Press [zPLAY] to clear the timer indicator
from the display.
The timer will start at the preset time, with the volume increasing
gradually to the preset level.
The timer comes on at the set time every day if the timer is on.
The unit must be in the standby mode for the timer to function.
If you turn the unit off and on again while the timer is functioning, the
finish time setting will not be activated.
When MUSIC PORT or iPod is selected as the source when the timer
comes on, the system turns on and engages MUSIC PORT or iPod as
the source. If you wish to playback from the portable audio equipment,
activate the equipment’s play mode and increase the volume. (See the
portable audio equipment’s instruction manual.)
•
•
•
•
•
•
•
Timer
This is a 12-hour clock.

Press [CLOCK/TIMER] to set the clock.
 Press [u, 2] or [i, 1] to select the time within 5 seconds.
(Press and hold to change the time faster.)
 Press [CLOCK/TIMER] again.
g To display the clock when the unit
is on
Press [CLOCK/TIMER]
Note
The clock is accurate to within ±60 seconds a month. Readjust if
necessary.
Set again after disconnecting the AC power supply cord or power
failure. •
•
Setting the time
Sleep timer
Play timer
30MIN 60MIN 90MIN 120MIN
Note
The remote control and main unit are factory-set to “REMOTE 1” mode.
If your remote control affects other equipment during operation, you can
switch to operate in “REMOTE 2” mode.
To switch to “REMOTE 2” mode

Press [FM/AM/MUSIC P.] to select “AM”.
 (While pressing [FM/AM/MUSIC P.] on the main unit)
Press and hold [2] until “REMOTE 2” appears on the main unit
display.
 Press and hold [ENTER] and [2] for at least 2 seconds.
The main unit and remote control are now set to operate in “REMOTE
2” mode.
To return to “REMOTE 1” mode
Perform steps 1 to 3 but use [1] instead of [2] for steps 2 and 3. (“REMOTE
1” appears on the main unit during step 2.)
The remote control cannot work with the main unit if their modes are
different.
“REMOTE 1” or “REMOTE 2” appears on the main unit when you operate
the remote control.*
* If “REMOTE 1” appears (The main unit is in “REMOTE 1” mode.)
Press and hold [ENTER] and [1] on the remote control for at least 2
seconds.
If “REMOTE 2” appears (The main unit is in “REMOTE 2” mode.)
Press and hold [ENTER] and [2] on the remote control for at least 2
seconds.
External unit (continued)
➡ Page 3 for the buttons position of remote control and main unit.
Note
Changing the main unit and remote control mode
SC-EN38_P,PC (RQTV0288)_running change1.indd 8 2/20/2008 9:55:09 AM