Philips Hopper 20 series - Manual (Page 21)

9. ADDITIONAL INFORMATION
Maintenance
21
English
LAMP REPLACEMENT
1. Press the STANDBY/ON/OFF button to switch off the
projector.
– The standby indicator lights up red.
2. Wait 5 minutes for the lamp to cool down and the cooling
fan to stop and disconnect the mains lead and all other
cables.
3. Turn the projector over. Never place the projector on the
side where the connections are located!
4. Unscrew and remove both horizontal adjusters.
5. Unscrew the screws at the bottom of the cover and
remove the cover.
6. Read the caution and warning labels on the lamp cover.
7. Unscrew the lamp holder.
8. Grasp the lamp holder handle and carefully pull the lamp
holder out of the projector.
Caution: Be very careful. The lamp holder may still be too
hot to touch.
Keep lamp holder opening to your right. Do not touch lamp
or point lamp holder opening at anyone.
Warning: The lamp may be hot. Be careful when handling.
Caution: A high-pressure lamp may break if handled
improperly.
9. Carefully remove the new lamp housing from its package.
Do not touch lamp or point lamp housing opening at
anyone. Do not drop, as the impact may cause the lamp to
break.
10. Place the lamp holder in the guiding slots and insert into
the lamp compartment.
11. Tighten the screws.
12. Replace the cover and tighten both the screws and the
horizontal adjusters.
13. Plug the projector back in by inserting the mains lead in the
POWER socket.
14. Press the STANDBY/ON/OFF button to switch on the
projector.
15. Reset the lamp life time (see ‘Resetting the lamplife time’).
16. Properly dispose of the old lamp.
Note: When replacing the lamp, always use the same type
of lamp (LCA 3108/00, 12NC: 8670 931 08009).
RESETTING THE LAMPLIFE TIME
1. Press MENU.
– The menu bar appears on the screen.
2. Use cursor control to select MISC(ellaneous) in the menu
bar.
3. LAMP LIFE is highlighted.
4. Press OK (–/– –) to activate the LAMP LIFE item.
5. Use cursor control to select RESET in the action window.
Note: If you select Quit, you will exit the action window and
the lamp life time will not be reset.
6. Press OK (–/– –) to confirm.
– A new action window
will appear
7. Use cursor control to select
YES or NO in the action
window and press OK (–/– –)
to confirm.
8. If required, select another
item you wish to adjust or
press MENU to exit.
M i s c .
L a m p l i f e
L a n g u a g e
H o r . m i r r o r
V e r . m i r r o r
C o u n t e r
S o u r c e P . P r e f .
R e c o n f i r m
Y e s N o
U s e c u r s o r c o n t r o l t o s e l e c t
P r e s s O K o r — t o a c c e p t
M i s c .
L a m p l i f e
L a n g u a g e
H o r . m i r r o r
V e r . m i r r o r
C o u n t e r
S o u r c e P . P r e f .
3 7 8 h o u r s u s e d
R e s e t Q u i t
U s e c u r s o r c o n t r o l t o s e l e c t
P r e s s O K o r — t o a c c e p t
M i s c .
L a m p l i f e
L a n g u a g e
H o r . m i r r o r
V e r . m i r r o r
C o u n t e r
S o u r c e P . P r e f .
U s e c u r s o r c o n t r o l t o s e l e c t
P r e s s O K o r — t o i n v o k e i t e m
P r e s s M E N U t o e x i t m e n u
Hopper SV10 Hopper SV10
Mouse
Data in
S-Video in
Video in
Audio
in Audio out
L R
Mouse
Data in
S-Video in
Video in
Audio
in Audio out
L
R
Pow er
Data
Audio
Video
Hopper SV10 Hopper SV10
Mouse
Data in
S-Video in
Video in
Audio
in Audio out
L R Mouse
Data in
S-Video in
Video in
Audio
in Audio out
L R
Pow er
Data
Audio
Video
Hopper SV10 Hopper SV10
Mouse
Data in
S-Video in
Video in
Audio
in Audio out
L R Mouse
Data in
S-Video in
Video in
Audio
in Audio out
L R
Pow er
Data
Audio
Video
Hopper SV10 Hopper SV10 Hopper SV10 Hopper SV10