Panasonic BT-3DL2550E - Manual (Page 53)

53
REMOTE Specifications
This monitor permits remote operation via GPI/RS-232C terminal.
GPI screen items correspond to the following terminals. Use the GPI menu to assign functions to each terminal (J page 39).
Functions assigned to terminals are executed when GND (pin 5) is short-circuited (ON) or open (OFF).
_ Operating conditions
Level operation: Operates when GND is short-
circuited.
Edge operation: Operates when GND changes from
open to short-circuited.
• When level operation is assigned to more than one
terminal, the function operates as long as one of
the terminals is short-circuited.
Edge operation should hold for 0.2 s or more after a
change.
*1 When a 16:9 marker and a 4:3 marker are simultaneously selected and activated on a 16:9 aspect ratio display,
both markers are displayed.
*2 When a 16:9 marker and a 4:3 marker are simultaneously displayed, the background of the marker selected by
the 16:9 marker is controlled.
*3 When “R-TALLY” and “G-TALLY” simultaneously go on, the tally color changes to orange.
GPI terminal
GPI Terminal (9P)
Pin number Signal
1 GPI1
2 GPI2
3 GPI3
4 GPI4
5 GND
6 GPI5
7 GPI6
8 GPI7
9 GPI8
Assigned item Function Operating conditions
UNDEF Undefined (no function assigned) —
MARKER1
ON/OFF
*1
Switches marker display defined in “GPI PRESET1”
(J page 26) in the “MARKER” menu.
Level operation
(Short-circuited: ON, Open: OFF)
MARKER2
ON/OFF
*1
Switches marker display defined in “GPI PRESET2”
(J page 26) in the “MARKER” menu.
Level operation
(Short-circuited: ON, Open: OFF)
MARKER
BACK HALF
*2
Reduces the brightness of the background outside the
marker displayed in “GPI PRESET1” (J page 26) to 50%.
Level operation
(Short-circuited: ON, Open: OFF)
MARKER
BACK BLACK
*2
Reduces the brightness of the background outside the
marker displayed in “GPI PRESET1” (J page 26) to 0%.
Level operation
(Short-circuited: ON, Open: OFF)
CENTER MARKER Turns the center marker display on and off. (When
other markers are displayed, this marker is
superimposed on other markers.)
Level operation
(Short-circuited: ON, Open: OFF)
INPUT SEL. VIDEO Switches the input line of the main window to VIDEO. Edge/level operation
INPUT SEL. SDI1 Switches the input line of the main window to SDI1. Edge/level operation
INPUT SEL. SDI2 Switches the input line of the main window to SDI2. Edge/level operation
INPUT SEL.
YP
B P R /RGB
Switches the input line of the main window to YP
B
P
R
/
RGB.
Edge/level operation
INPUT SEL. DVI-D Switches the input line of the main window to DVI-D. Edge/level operation
SD ASPECT Sets the aspect ratio for SD signal input in the main
window or sub-window single screen display.
Level operation
(Short-circuited: 16:9, open: 4:3)
SCAN Switches between “UNDER” and “NORMAL” scan
modes in the main window or sub-window single
screen display.
Level operation (Short-circuited: UNDER,
Open: NORMAL)
R-TALLY *3 Lights the red tally. Level operation
(Short-circuited: ON, Open: OFF)
G-TALLY *3 Lights the green tally. Level operation
(Short-circuited: ON, Open: OFF)
MONO Switches between color and monochrome (MONO).
(Disabled during PC signal input)
Level operation (Short-circuited:
monochrome, Open: color)
GAMMA SEL. FILM Switches the gamma curve in the main window to
FILM mode.
Level operation (Short-circuited: FILM
mode, Open: STANDARD mode)
GAMMA SEL. STDIO/
PST
Switches the gamma curve in the main window to
STDIO/PST mode.
Level operation (Short-circuited: STDIO/
PST mode, Open: STANDARD mode)
SELECT SYNC Selects the SYNC when using YP
B
P
R
and RGB-
VIDEO input.
Level operation
(Short-circuited: EXT, Open: INT)
2D ONLY
2D ONLY
2D ONLY
2D ONLY
2D ONLY
BT-3DL2550PE(VQT2U10)_E.book 53 ページ ２０１０年７月８日 木曜日 午後２時１２分