Philips 19PR09C - Manual (Page 3)

IN
OUT
OR
ANT.IN
Y our Cable TV signal may be
a single (75
Ω
) cable or a
Cable Box installation. In either
case, the connection to the TV
is very easy.
C ABLE TV
C ABLE /C ABLE B OX
If you do not have a
Cable Box, then you're ready
to connect your Cable TV sig-
nal to the TV. Go to step 2.
If you have a Cable Box:
Connect the Cable TV signal
to the IN jack on the Cable
Box.
If you do not have a
Cable Box, connect the Cable
TV signal directly to the
ANT(enna) IN jack on the TV.
If you have a Cable Box:
Use a coaxial cable to connect
the OUT jack of the Cable Box
to the ANT(enna) IN jack on
the TV.
NOTE: The coaxial cable
might be supplied by the Cable
TV company.
Back of TV
Coaxial cable
Cable Box
To select
only the channels on
your Cable system,
see Auto Install
(page 4).
If you use a Cable
Box, set the TV to
the same channel as
the CH 3/4 switch
on the back of the
Cable Box and
select channels at
the Cable Box.
S MART
H ELP
Cable TV Company
Cable TV Signal (75
Ω
)
Note to the Cable TV System Installer:
This reminder is provided to call the Cable TV
system installer’s attention to Article 820-40 of
the National Electrical Code, which provides
guidelines for proper grounding - in particular,
specifying that the cable ground shall be connect-
ed to the grounding system of the building, as
close to the point of cable entry as possible.
H
OOKING
U
P
Y
OUR
TV (A
NTENNA
/C
ABLE
C
ONNECTIONS
) (C
ONT
’
D
)
- 3 -
F or more convenient tape
playback from a camcorder
or VCR, use the AUDIO and
VIDEO In jacks on the front of
the TV. These easily accessible
jacks allow quick connections
between the TV and the VCR
or camcorder.
U SING THE F RONT A UDIO /V IDEO I N J ACKS
A UDIO /V IDEO I N J ACKS
Connect a video
cable (not supplied) to the
VIDEO OUT jack of the
camcorder/VCR and to the
VIDEO In jack on the front
of the TV.
When you are
finished watching
the tape, press the
TV/AUX button on
the TV remote con-
trol to return to
viewing normal TV
channels.
If the VCR or cam-
corder has Right
and Left AUDIO
OUT jacks, you will
need a “Y” connec-
tor cable in order
to connect the cam-
corder/VCR to the
TV. Or, check the
owner’s manual of
the camcorder or
VCR. It may explain
how to connect to
a TV that has a sin-
gle AUDIO In jack.
S MART
H ELP
When you play a tape,
select A/V IN at the TV.
Press the TV/AUX button
to select A/V IN. A/V IN will
appear on the screen.
Connect an audio cable
(not supplied) to the
AUDIO OUT jack of the
camcorder/VCR and to the
AUDIO In jack on the
front of the TV.
Turn on the cam-
corder/VCR and press the
PLAY button on the cam-
corder/VCR.
When you are finished
watching the tape, press
the STOP button on the
camcorder/VCR.
CHANNEL VOLUME EARPHONE VIDEO MENU AUDIO POWER
VIDEO
OUT
AUDIO
Video Cable (yellow) from
VIDEO OUT to VIDEO In
Audio Cable (white) from
AUDIO OUT to Audio In
1
2
RF/ANTENNA OUT ANTENNA IN
ANT.IN STOP/EJECT
RECORD
MENU STATUS/EXIT
F.FWD PAUSE REW
CHANNEL VCR/TV
PLAY
VIDEO L AUDIO R POWER
T he basic Antenna/Cable to
VCR to TV connection is
shown here. If you have a Cable
Box, refer to the VCR owner’s
manual for details.
VCR TO TV
B ASIC C ONNECTION
Connect your
Antenna or Cable signal to
the ANTENNA IN jack on
the VCR.
Connect a coaxial
cable to the RF OUT
or ANTENNA OUT
jack on the VCR and to
the ANT(enna) IN jack
on the TV.
The coaxial cable may be
supplied with the VCR.
Coaxial cable
Outdoor
VHF/UHF
Antenna
300 to 75 Ω
Adaptor
Cable TV signal
Back of TV
Refer to the VCR
owner's manual for other
possible connections and for
operating details.
VCR
(example only)