Panasonic MC-CG663 - Manual (Page 7)

Indicator for replacing the dust bag
Turn the power control to the highest setting and lift the nozzle
off the floor. If the dust indicator turns red, the dust bag is full
and requires replacing the dust bag.
NOTE: If the dust bag is not properly installed, the cover will
not close. Be sure to check that the bag is properly
installed before operating, otherwise dust will leak
out.
The dust bag can easily lay on the dust cover packing
or clip between bag collar and body, so be sure to
properly extend it into the vacuum cleaner body.
Replacing the dust bag
D-1 Lift dust cover, catch and raise dust cover until it
clicks properly.
D-2 Remove bag collar from bag holder and pull out
dust bag.
D-3 Set the dust bag.
D-4 Close dust cover.
Floor nozzle
D-5 Inspect once a month.
Using an old toothbrush or similar tool, clean any dirt
or lint from the brush.
Turbine nozzle
D-6 After removing the brush cover with a coin, remove the
beater bar from the belt.
Then cut across threads, strings, hairs, etc. from the
beater bar with a pair of scissors. (Removal as per
reverse procedure)
NOTE: Take care not to cut the brush.
Do not wash in water.
Vacuum cleaner body
D-7 Wipe with a soft cloth soaked with water.
Maintaining the Pre-motor Filter
Perform the procedure given below when the suction power is
not restored after maintaining the filter.
D-8 Open the dust cover.
D-9 Remove the pre-motor filter.
D-10 Wash gently with water and then allow to dry in a
shaded location.
D-11 Replace to its original location.
NOTE: Make sure you remember to replace the filter. If the
filter is not installed, it will cause motor failure.
• Do not wash the filter in a washing machine or dry it with a
dryer or other source of hot air.
Filter care
D-12 Exhaust filter
Exhaust air filter,is installed in the rear side of the
vacuum cleaner.
This filter retains any small dust particles which may
be present in the expelled air. It is advisable to change
the clean air filter when it becomes dirty. To change the
clean air filter,hold the exhaust cover (as illustrated)
and pull it out.
After changed the filter, set the exhaust cover to
original position(as illustrated).
NOTE:
IMPORTANT: Never use the cleaner without the correct
filters properly installed. Failure to do so may
result in damage to the motor.
What to do if your cleaner does not work
Check that the appliance is correctly plugged in and that the
electrical socket is working. In case that the thermal cut-out
device has operated, wait until it resets after approximately
60 minutes.
If after having checked the mentioned points, the cleaner
does not work, take it to an Authorised Service Centre to be
repaired.
What to do when the suction performance
reduces
• Stop the cleaner and unplug from the socket.
• Check whether the wans, hose and accessories are blocked
or not.
If they are blocked, remove the obstruction.
• Check that the dust bag is full.
If it is full, replace it.
• Check that Pre-motor Filter or Exhaust Filter is blocked with
dust.
If they are blocked, clean them out or replace.
REMINDER FOR CUSTOMER
The model and serial number of this product may be found on
the nameplate located at the underside of your cleaner. You
should note the model and serial number in the spaces
provided and retain this book as a permanent record of your
purchase.
Model Number. ......................................................................
Serial No. ...............................................................................
Date Purchased. ....................................................................
Where Purchased. .................................................................
5
D - MAINTENANCE AND SERVICING
CAUTIONS
• The plug must be removed from the socket-outlet
before cleaning or maintaining the appliance.
• To avoid injury, keep your fingers and hands away
from the beater bar.
• DO NOT use hot air or hot surface to dry filters. Keep
at room temperature for approximately 24 hours.
• IMPORTANT: Before re-installing the washable filters,
make sure they are completely dry to avoid damaging
the cleaner.
MC-CG663
MC-CG663K
230-240 V~50 Hz
2000 W
1500-1600 W
280 mm x 430 mm x 260 mm
5.1 kg
Telescopic
√
√
MC-CG661
MC-CG661K
√
√
SPECIFICATIONS
Power source
Max. Input
Nominal input
Dimensions
(W x L x H)
Net weight
Extension
wand
Crevice nozzle
Dusting brush