Panasonic SC-HT790V - Manual (Page 46)

46
RQT6951
The radio
Preparation
≥Press [TUNER] to put the remote control in TUNER mode.
≥Press [Í] to turn on the unit.
≥Press [FM/AM] to select “FM” or “AM” as the source.
1
Press [ 6] or [5] to select the
frequency of the required station.
TUNED: Displayed when a radio station is
tuned.
ST: Displayed when a stereo FM
broadcast is being received.
Press and hold [ 6] or [5] until the frequency starts
scrolling to start automatic tuning. Tuning stops when a
station is found.
2
Adjust the volume.
∫ If noise is excessive in FM
Press [PLAY MODE] to display “MONO”.
Press [PLAY MODE] again to cancel the mode.
The mode is also canceled when you change the
frequency.
∫ FM frequency step
The step is factory-set to 0.2 MHz, but you can change it to receive
broadcasts allocated 0.1-MHz steps.
1 Press [FM/AM] to select “AM”.
2 Press and hold [FM/AM].
After a few seconds the display changes to show the current
minimum frequency. Continue to hold the button down. The
minimum frequency changes and the step is changed.
To return to the original step, repeat the above steps.
[Note]
Any FM and AM frequencies preset in channels will be initialized by
this procedure. Preset them again.
Preset channels to make selection simple.
Up to 15 stations can each be set in the FM and AM bands.
1
Tune to “FM 87.9” MHz or “FM
87.5” MHz (
➡ left).
2
Press and hold [ENTER].
Release the button when “AUTO” is displayed.
The tuner presets all the stations it can receive into the
channels in ascending order.
“SET OK” is displayed when the stations are set. The last
station to be set is then played.
3
Tune to “AM 520” kHz.
4
Press and hold [ENTER].
“ERROR” is displayed
Presetting was unsuccessful. Preset manually.
1
Tune to the station (
➡ left).
2
Press [ENTER].
3
While “PGM” is flashing
Press the numbered buttons to select
a channel.
Alternatively, press [ 3 CHW]
or [ 4 CHX] then press
[ENTER].
The station occupying a channel is
erased if another station is preset in that channel.
1
Press [FM/AM] to select “FM” or
“AM”.
2
Press the numbered buttons or
[
3 CHW] or [4 CHX] to select the
channel.
To select a 2-digit number
Example: To select channel 12, press [
S10] ➡ [1] ➡ [2]
[Note]
The unit of display is MHz for FM radio and kHz for AM radio when
the selector is in TUNER mode.
Manual tuning
DVD/VCR
DVD
RESET
TV/VIDEO
PAGE
GROUP
PICTURE MODE/
SETUP
REPEAT
PLAY MODE
TV VOLi JET REW TV VOLj
OPEN/CLOSE/EJECT
TOP MENU
NAVI
PROG CANCEL SPEED
CH
CH
OSD/DISPLAY
VOLUME
D.RE-MASTER
SUBWOOFER
POSITION
MEMORY SUBTITLE ZOOM QUICK REPLAY
C.S.M
SFC
C.FOCUS
SUPER SRND
S.POSITION
MUTING
SLEEP
Î PL [SHIFT] AUDIO
MIX 2CH
TEST
CH SELECT
RETURN
DIRECT
NAVIGATOR
PLAY LIST
MENU
SLOW/SEARCH SKIP
1
100
2 3
4 5 6
7 8
0
9
TV TUNER
FM/AM REC
ENTER
VCR
S 10/ENTER
FM/AM
TUNER
6 5
PLAY MODE
3 CH W
4 CH X
ENTER
VOLUME
s r
Í
Numbered
buttons
TUNEDST
MONO
Preset tuning
Automatic presetting
Manual presetting
Selecting channels
PGM