Pioneer VSX-D909S - Manual (Page 44)

44
Selecting a Sound Mode
To ensure the best possible surround sound, be sure to complete the set up procedures described in “Setting
Up for Surround Sound” (starting on page 29) before using the sound modes. This is particularly important when
using the 2 (Dolby) Digital or DTS sources. When using the sound modes, using SPEAKERS A will give the
best results. If you use SPEAKERS B the sound will be down mixed to the two front B speakers and the
surround sound effect will be lost.
AV PRE-PROGRAMMED AND LEARNING
REMOTE CONTROL UNIT
S0URCE
DVD/LD TV/SAT VCR1 VCR2
CD
TV VOL
TV FUNC
MENU
ENTER
STEREO/
DIRECT DSP
LIGHT
MUTE
TV
VOLUME
MD/
TAPE1 TUNER TVCONT
RECEIVER
USE SETUP
MULTI
OPERATION
CLASS MPX DIRECT ACCESS
CHANNEL
STATION
TV CONTROL
FUNCTION
REMOTE SETUP
SYSTEM SETUP
INPUT
ATT
MIDNIGHT MULTI CH
INPUT
STANDARD
DIGITAL NR
EFFECT/
CH SEL
SIGNAL
SELECT
BAND
SYSTEM
OFF
1 2 3
4 5 6
7 8 9
0
Î
¶ 8 7 3
1 ¡ 4 ¢
+ -
+ -
+ -
MULTI CONTROL
+ +
– –
+
–
STEREO/
DIRECT
STANDARD
ADVANCED
+/
EFFECT/
DSP
ADVANCED
DISC
EXIT
+10
GUIDE
ENTER
CH SEL
DTV ON/OFF DTV MENU
TUNING
/DTS
1
Basic Playback
1 Put the remote control side switch
in USE.
2 Select the sound mode.
• For STANDARD \ Press STANDARD
Each press changes the STANDARD mode as
follows:
STANDARD STANDARD 7.1
• For ADVANCED THEATER
\ Press ADVANCED
Each press changes the ADVANCED THEATER
mode as follows:
MUSICAL DRAMA
ACTION 5/7-D THEATER
• For DSP modes
\ Press DSP(DSP MODE)
repeatedly
Each press changes the DSP mode as follows:
HALL 1 HALL 2 JAZZ
5/7CH STEREO THEATER 2 THEATER 1
DANCE
• For STEREO
\Press STEREO/DIRECT
Each press changes the STEREO mode as follows:
STEREO DIRECT
• If you have SURROUND BACK speakers switched
on (see p.32-33) then 7-D THEATER and 7CH
STEREO will appear as such in the display on the
receiver. If these speakers are not switched on the
above two modes will appear as 5-D THEATER and
5CH STEREO.
• The effects of ADVANCED THEATER mode can be
adjusted in the range of 10 to 90 by pressing
EFFECT +/– (The default setting is 70). Also, the
effect level can be set in each ADVANCED THE-
ATER mode by pressing the EFFECT(+/–) button.
• The amount of effect of each DSP mode can be
adjusted in the range of 10 to 90 (the default
setting value is 70) by pressing EFFECT +/–.
• 5/7CH STEREO modes cannot be changed.
memo
STANDBY/ON DSP MODE
SIGNAL SELECT ADVANCED STANDARD
STANDBY
AUDIO/VIDEO MULTI-CHANNEL RECEIVER
STEREO/ DIRECT
/DTS
PHONES S-VIDEO VIDEO
MULTI CH INPUT
FL DIMMER
TAPE 2 MONITOR
TONE CHANNEL SELECT LOUDNESS DIGITAL NR CLASS BAND
TUNER CONTROL
MEMORY MPX VIDEO
SELCT SPEAKERS
- TUNIN
- STATIO - TREBLE + - BASS +
L AUDIO R
VIDEO INPUT
Digital Signal Processor VSX-D909S
DSP MODE
STEREO/
DIRECT
STANDARD SIGNAL SELECT
ADVANCED