The initial setup menu 15 – Pioneer RCS-LX60D User Manual
Page 144
The Initial Setup menu
15
144
En
D.TV Age Limit
Next Screen
Use this screen to enter an age limit for D.TV programmes. Programmes
that are broadcast with age suitability guidelines that fall above the age set
here will require the correct password to be entered before the channel can
be viewed.
You must also enter your password in order to change the age limit setting.
This setting is only applicable when the country is set to France, Denmark, Finland or Sweden.
HDMI Output
(only available when an HDMI device is connected)
Screen Resolution
1920 x 1080p
Constant 1920 x 1080p output.
1920 x 1080i
Constant 1920 x 1080i output.
1280 x 720p
Constant 1280 x 720p output.
720 x 576p
(720 x 480p)
Constant 720 x 576p output (when setting the
Input Line System
to
525 System
, video is output in 720 x 480p).
720 x 576i
(720 x 480i)
Constant 720 x 576i output (when setting the
Input Line System
to
525 System
, video is output in 720 x 480i).
• If you choose a setting that is incompatible with your TV you may not be able to see any picture at all. In this case, press
OPEN/CLOSE
while
holding down the
(Stop) button on the front panel to switch the setting (this also switches Component Video Out
on page 139
to the default
setting).
• If you have the
Colour
set to
YCbCr 4:2:2
, you cannot select
720 x 576i (720 x 480i)
.
4:3 Video Output
Full
Select if your HDMI TV allows you to change the aspect ratio.
Normal
Select if your HDMI TV does not allow you to change the aspect ratio. 4:3
video will be shown with bars on each side.
Colour
RGB (0–255)
Use if colours are weak and black appears to ‘float’ on the
RGB (16–235)
setting.
RGB (16–235)
Use this setting if colours appear overly rich and the black too deep on the
RGB (0–255)
setting.
YCbCr 4:2:2
The video signal is output as a 10-bit YCbCr 4:2:2 component signal. This is
the standard setting for HDMI-compatible devices.
YCbCr 4:4:4
The video signal is output as a 8-bit YCbCr 4:4:4 component signal.
• Depending on the connected device some settings may not be available.
• When a DVI device is connected, the
YCbCr 4:2:2
and
YCbCr 4:4:4
options are not available.
• You cannot choose
YCbCr 4:2:2
when the
Screen Resolution
is set to
720 x 576i (720 x 480i)
.
Audio Output
Auto •
Dolby Digital, MPEG and DTS sources are output as a bitstream signal.
However, depending on the
Audio Out
setting, number of audio channels,
and the HDMI-connected device, Linear PCM audio may be output.
PCM
All audio signals are converted to Linear PCM (except DTS).
Bitstream Priority
Select if the connected device is compatible with bitstream audio.
This setting is not available when a DVI device is connected
.
Options
On Screen Display
On •
The recorder displays operation displays (
Stop
,
Play
, etc.) on-screen.
Off
Switches off the on-screen operation displays.
Front Panel Display
On •
The time is shown in the front panel display when the recorder is in standby.
Off
The front panel display is switched off in standby.
Setting
Options
Explanation
DVRLX60D_WV_EN.book 144 ページ ２００７年４月２４日 火曜日 午後７時５８分