NordicTrack APEX6100 NTTL24992 - Manual (Page 13)

When you select a preset program, the left side of
the main display will flash the maximum incline
setting of the program and the right side of the
display will flash the maximum speed setting of
the program for ten seconds. Three seconds after
a preset program is selected, the name of the
selected program and the total program time will
begin to scroll across the main display.
The program dis-
play will show the
speed settings for
the program you
have selected.
Note: Depending
on the length of the program, the program display
may not show the last settings for the program.
Press the Start Program button or the Speed +
button to start the program.
A moment after the button is pressed, the tread-
mill will automatically adjust to the first speed and
incline settings for the program. Hold the handrails
and begin walking.
Each program is divided into several time segments
of different lengths. The main display shows both
the time remaining in the program and the time re-
maining in the current segment of the program.
One speed setting
and one incline
setting are pro-
grammed for each
segment. The
speed setting for
the first segment
is shown in the
flashing Current Segment column of the program
display. (The incline settings are not shown in the
program display.) The speed settings for upcoming
segments are shown in the columns to the right.
When only three seconds remain in the first seg-
ment of the program, both the Current Segment
column and the column to the right will flash, a se-
ries of tones will sound, and all speed settings will
move one column to the left. The speed setting for
the second segment will then be shown in the
flashing Current Segment column and the tread-
mill will automatically adjust to the speed and in-
cline settings for the second segment.
The program will continue in this way until the
speed setting for the last segment is shown in the
Current Segment column and no time remains in
the program. The walking belt will then slow to a
stop.
Note: Each time a segment ends and the speed
settings move to the left, if all of the indicators in
the Current Segment column are lit, the speed set-
tings may move downward so that only the highest
indicators in the columns will appear in the pro-
gram display. When the speed settings move to
the left again and not all of the indicators in the
Current Segment column are lit, the speed settings
will move back up.
If the speed or incline setting for the current
segment is too high or too low, you can manually
override the setting by pressing the Speed or
Incline buttons on the console. Every few times
one of the Speed buttons is pressed, an additional
indicator will light or darken in the Current Segment
column. If any of the columns to the right of the
Current Segment column have the same number
of lit indicators as the Current Segment column,
an additional indicator may light or darken in those
columns as well. Note: If you manually adjust the
speed setting so that all of the indicators in the
Current Segment column are lit, the speed settings
in the program display will not move downward as
described above. Note: If you manually override
the speed or incline setting for the current seg-
ment, when the segment ends the treadmill will
automatically adjust to the speed and incline
settings for the next segment.
To stop the program temporarily, press the Stop
button. The time will begin to flash in the main dis-
play. To restart the program, press the Start
Program button or the Speed + button. To end the
program, press the Stop button, remove the key,
and then reinsert the key.
Follow your progress with the displays.
See step 5 on page 11.
Measure your heart rate if desired.
See step 6 on page 12.
When the program has ended, remove the key.
Step onto the foot rails and make sure that the in-
cline of the treadmill is at the lowest level. Next,
remove the key from the console and put it in a se-
cure place. Note: If the displays and indicators
on the console remain lit after the key is re-
moved, the console is in the “demo” mode.
Refer to page 24 and turn off the demo mode.
When you are finished using the treadmill, move
the on/off switch near the power cord to the off
position and unplug the power cord.
6
5
4
3
Current Segment
13