Nady Systems MXE-1212 - Manual (Page 13)

S P E C I F I C AT I O N S
13
The specifications above are correct at the time of printing of this manual. For improvement purposes, all specifications for this unit,
including design and appearance, are subject to change without prior notice.
3. FREQUENCY RESPONSE
ANY INPUT TO
ANY OUTPUT ....................20 Hz to 20 KHz =/- 3dB @ 0 dBm
4. TOTAL HARMONIC DISTORTION
ANY INPUT TO
ANY OUTPUT ..............0.02%, 20 Hz-20 KHz @ 1Khz, 0 dBm
5. INPUT CHANNEL EQUALIZATION
High shelving ....................12 KHz, +/- 15 dB, Q fixed at 2 oct.
Mid bell ............................2.5 KhZ, +/- 15 dB, Q fixed at 1 oct.
Low shelving ......................80 Hz, +/- 15 dB, Q fixed at 2 oct.
6. MASTER MIX EQUALIZATION
7 band (63Hz,150Hz,400Hz,1KHz,2.5KHz,6.4KHz,15KHz),
+/-12dB
7. GAIN CONTROL RANGE
Input channel trim control....Stop to stop- Mic +10 dB~+60 dB,
Line +10 dB~+40 dB
Channel/Master/Effect Faders ............................ -
∞
to +15 dB
Aux Send/Aux Master Send ................................Off to +15 dB
Aux Return............................................................Off to +20 dB
Channel and Master Effect Sends........................Off to +15 dB
8. CROSSTALK @ 1KHZ
ADJACENT CHANNEL INPUTS ......................-78 dB~-68 dB
INPUT TO OUTPUT .......................................... -78 dB~-68 dB
9. HUM AND NOISE
20 Hz-20 KHz, Rs=150 ohms, input TRIM @ 0 dB, input sen-
sitivity at –60 dB
EQUIVALENT INPUT NOISE ....................................-129 dBm
RESIDUAL OUTPUT NOISE......................................< 90 dBm
10. VU METERS
10-segment LED X 2
11. PHANTOM POWER
+48 VDC, globally selected
12. POWER REQUIREMENTS
Voltage selectable, 120VAC/60Hz or 230VAC/50Hz
13. FUSE
115VAC Operation ......................................2A, 5x20mm, 250V
230VAC Operation ......................................1A, 5x20mm, 250V
14. POWER CONSUMPTION
12W
15. DIMENSIONS AND WEIGHT
16” x 17” x 3.5” (406 x 432 x 89 mm), 14.7 lbs (6.7 Kg)
1. INPUT SECTION
Input Connector Input Impedance Nominal Level Max Level
MONO CH MIC XLR >1.3K
Ω
+2 dBm +14 dBm
MONO CH LINE 1/4" TRS >10K
Ω
+4 dBm +22 dBm
STEREO CH LINE 1/4" TS >10K
Ω
+4 dBm +22 dBm
TAPE IN RCA PIN JACKS >10K
Ω
+2 dBm +22 dBm
AUX RETURNS 1/4" TS >10K
Ω
+4 dBm +22 dBm
INSERT IN 1/4" TRS >10K
Ω
+4 dBm +22 dBm
2. OUTPUT SECTION
Output Connector Output Impedance Nominal Level Max Level
STEREO OUT L/R XLR & 1/4" TRS 120
Ω
+4~+6 dBm +22 dBm
AUX SENDS 1/4" TS 120
Ω
+4~+6 dBm +20 dBm
INSERT OUT 1/4" TRS 120
Ω
+4~+6 dBm +22 dBm
REC OUT RCA PIN JACKS 1K
Ω
+4~+6 dBm +22 dBm
PHONES 1/4" TRS 200
Ω
––– 40mW X 2