Napoleon Fireplaces EF31H - Manual (Page 7)

7
W415-0469 / A / 01.04.05
This fireplace requires a 15 amp, 120 volt and 60 hz
circuit. The fireplace should be on its own circuit. If
there are other appliances on the same circuit, this may
cause the circuit breaker or fuse to blow when the fire-
place heater is in operation.
The unit comes with a 6' electrical cord, exiting the bot-
tom right side. Plan your installation to avoid the use of
an extension cord. If you require an extension cord, it
must be at least 16 awg wire and be rated for 2025
watts.
Electrical outlet wires must comply with local building
codes to reduce the risk of fire, electrical shock and
injury.
Do NOT use the fireplace if any part has been under
water.
Call a qualified service technician IMMEDIATELY to have
the fireplace inspected for damage to the electrical cir-
cuit.
If it is necessary to hard wire this fireplace, a qualified If it is necessary to hard wire this fireplace, a qualified If it is necessary to hard wire this fireplace, a qualified If it is necessary to hard wire this fireplace, a qualified If it is necessary to hard wire this fireplace, a qualified
electrician may remove the cord connection, and wire
electrician may remove the cord connection, and wire electrician may remove the cord connection, and wire electrician may remove the cord connection, and wire electrician may remove the cord connection, and wire
this unit directly to the house hold wiring.
this unit directly to the house hold wiring. this unit directly to the house hold wiring. this unit directly to the house hold wiring. this unit directly to the house hold wiring.
Permanently framing the fireplace with an enclosure, re-
quires the fireplace to be hardwired.
This fireplace must be electrically connected and grounded
in accordance with local codes, if hard wired. In the ab-
sence of local codes, use the current CSA C22.1 CANADIAN
ELECTRICAL CODE in Canada or the ANSI/NFPA 70-1996
NATIONAL ELECTRICAL CODE in the United States.
ELECTRICAL CONNECTION
HARD WIRING CONNECTION
ELECTRICAL DIAGRAM LEGEND
1. 1. 1. 1. 1. Power (Rocker Switch) Power (Rocker Switch) Power (Rocker Switch) Power (Rocker Switch) Power (Rocker Switch) W660-0023 W660-0023 W660-0023 W660-0023 W660-0023
2. 2. 2. 2. 2. Thermostat Switch Thermostat Switch Thermostat Switch Thermostat Switch Thermostat Switch W660-0040 W660-0040 W660-0040 W660-0040 W660-0040
3. 3. 3. 3. 3. Fan / Heater Assembly Fan / Heater Assembly Fan / Heater Assembly Fan / Heater Assembly Fan / Heater Assembly W062-0019 W062-0019 W062-0019 W062-0019 W062-0019
4. 4. 4. 4. 4. Main Circuit Board Main Circuit Board Main Circuit Board Main Circuit Board Main Circuit Board W707-0003 W707-0003 W707-0003 W707-0003 W707-0003
5. 5. 5. 5. 5. DC Motor (flame effect) DC Motor (flame effect) DC Motor (flame effect) DC Motor (flame effect) DC Motor (flame effect) W435-0006 W435-0006 W435-0006 W435-0006 W435-0006
6. 6. 6. 6. 6. Main Power Cord Main Power Cord Main Power Cord Main Power Cord Main Power Cord W750-0143 W750-0143 W750-0143 W750-0143 W750-0143
7. 7. 7. 7. 7. Strain Relief Strain Relief Strain Relief Strain Relief Strain Relief W105-0002 W105-0002 W105-0002 W105-0002 W105-0002
8. 8. 8. 8. 8. Flame Effect Light Flame Effect Light Flame Effect Light Flame Effect Light Flame Effect Light W750-0126 W750-0126 W750-0126 W750-0126 W750-0126
(two light sockets- (two light sockets- (two light sockets- (two light sockets- (two light sockets-75quartz watts max 75quartz watts max 75quartz watts max 75quartz watts max 75quartz watts max)))))
9. 9. 9. 9. 9. Nylon Cable Tie Nylon Cable Tie Nylon Cable Tie Nylon Cable Tie Nylon Cable Tie
Electric Diagram
OPTIONAL SCREEN INSTALLATION
1. Bunch the curtain mesh in the middle of the rod.
2. Insert one end of the rod through the hole indicated in the side
of the firebox frame.
3. The rod will need to be bowed in the middle in order to insert the
other end of the rod into the opposite hole.
4. Tuck the bottom of the curtain mesh behind the front lip of the
retainer.