Numark Industries CDN-32SE - Manual (Page 8)

CDN-32SE
- The Leader in DJ Technology
©2001 Numark Industries - 8 - http://www.numark.com
DESCRIPTION CDN-32SE REMOTE FEATURES
1. OPEN/CLOSE (Disc Tray Open/Close) - Press to load or eject
the disc. Each press will open or close the disc tray on the
transport. NOTE: Tray will not open unless the disc has been
paused. Tray will automatically close after 30 seconds.
2. TIME (Time Button) - Switches the time display between
elapsed playing time and remaining time on the track and
remaining time on the entire CD.
3. CONT/SING - Will cause just a single track to play or all tracks
in order by pressing once or twice.
4. LCD DISPLAY - Indicates all the functions, as they are
occurring, with the CD. These functions are explained in the
next section.
5. TRACK (Track Buttons) - Used to select the track to be played.
6. Track 10 Button - This button is for quickly advancing to higher
tracks on a CD.
7. PROGRAM - Depress this button and the unit will stop and the
program indicator will light. Select each track to be programmed
and press the PROGRAM button between selections. You can
program up to 30 tracks. Press PLAY to start the program. To
exit and erase program, either hold the program button down for
more than 2 seconds while the unit is stopped, open the disc
tray, or turn off the power.
8. PITCH (Pitch Button) - Activates the Pitch Slider.
9. PITCH SLIDER - The pitch can be changed up to +/-12% by
pressing the PITCH button so the PITCH LED is lit, then moving
the sliding fader. The pitch will not be changed if the PITCH
LED is off.
10. SEARCH WHEEL (OUTER RING) - 3 forward and 3 reverse
speed positions for searching through songs. The more you
turn the wheel in either direction the faster you search through
the music.
11. PITCH BEND/JOG WHEEL (INNER RING) - The jog wheel serves
2 functions depending on the current mode.
• The jog wheel will control a slow frame search when the CD is not
playing. To set a new frame cue point, spin the wheel then press
play when you have determined the proper position. Press CUE to
return to the “CUE POINT”.
• When both CD players are playing a CD, the pitch bend function
allows the positioning of the bass beats to be matched after the
pitch of each disc is matched. Either player can “catch up” or “fall
back” to match the other player. The jog wheel will temporarily bend
the pitch of the music if the song is already playing by rotating the
wheel clockwise to speed up or counterclockwise to slow down. By
changing the pitch of one disc with respect to the pitch of the other
disc, the beats can be matched.
12. CUE - Pressing the CUE button during play provides a return to the
position at which play was started. If PAUSE is used before CUE,
that will become the cue point. Alternately pressing the PLAY
button and the CUE button allows the CD to be played from the
same position any number of times. The CUE LED will light up from
the time the CUE button is pressed until the CD has been reset to
the position at which play was started. Steady lighting of this LED
indicates the ready condition.
13. START/PAUSE (Play/Pause Button) - Each press of the
Play/Pause Button causes the operation to change from play to
pause or from pause to play.
14. LOOP BUTTONS
LOOP IN - Used for setting a start loop point and new cue points
during play.
LOOP OUT - Used for setting the end loop point and releasing the
loop action.
RELOOP/STUTTER - Depending on mode, as explained further,
this button is used for either repeating a previously set loop or
seamlessly stuttering on the last set cue point.
15. RELAY/FADER START– Pressing this offers 2 functions. If the
players are set in single mode it will alternate (relay) between
players after each track or in Continuous after each CD. This also
activates the Fader Start function in you CD player when connected
to compatible fader start mixer.