Runco CW-50MC - Manual (Page 27)

26
* NOTE: Make sure to use commands for adjusting sub-volume (SV1~5) after first switching to the prescribed
input using the input switching commands (IN1~5).
Command
Name
Full Name RS-232C
Adjustment
Validity
Normal
Validity
Numerical
Direct
Validity
Function
P PLN BRT. ENHANCE: OFF ○ Turns the center brightness enhancement OFF.
PLY BRT. ENHANCE: ON ○ Turns the center brightness enhancement ON.
POF - ○ ○ Power OFF.
PON - ○ Power ON.
PUC CINEMAMODE: ###### ● Displays the current CINEMAMODE setting.
PUCS00 CINEMAMODE: OFF ○ Turns CINEMAMODE OFF.
PUCS01 CINEMAMODE: STANDARD ○ Sets CINEMAMODE to STANDARD.
PUCS02 CINEMAMODE: ADVANCE ○ Sets CINEMAMODE to ADVANCED.
R RHI R. GAIN: *** ○ ○ Adjusts R. HIGH.
RLW R. OFFSET: *** ○ ○ Adjusts R. LOW.
RSL R SIDEBAR ADJ. LEVEL: *** ○ ○ Adjusts the RED side mask.
S SFT SIGNAL FORMAT: #### ● Displays the current SIGNAL FORMAT.
SFTS01 SIGNAL FORMAT:
VGA or XGA or SXGA or 720PC
○ Sets the SIGNAL FORMAT to PC FORMAT 1
(VGA or XGA or SXGA or 720PC).
SFTS02 SIGNAL FORMAT:
WVGA or WXGA or SXGA+
○ Sets the SIGNAL FORMAT to PC FORMAT 2
(WVGA or WXGA or SXGA+).
SFTS03 SIGNAL FORMAT:
VIDEO 525p or VIDEO 750p
○ Sets the SIGNAL FORMAT to VIDEO 525p or VIDEO 750p.
SFTS04 SIGNAL FORMAT: PC AUTO ○ Sets the SIGNAL FORMAT to PC AUTO.
SHP SHARPNESS: *** ○ ○ Adjusts the SHARPNESS.
SIM SIDEBAR ADJ. MODE: ###### ● Displays the current side mask setting.
SIM01 SIDEBAR ADJ. MODE: NORMAL ○ Sets the sidebar adjustment setting to normal.
SIM02 SIDEBAR ADJ.: OVERLAY1 ○ Sets the sidebar adjustment setting to OVERLAY1.
SIM03 SIDEBAR ADJ.: OVERLAY2 ○ Sets the sidebar adjustment setting to OVERLAY2.
SLN - ○ Turns the STILL setting to OFF.
SLY STILL ○ Turns the STILL setting to ON.
SSI ######## ● ● Displays the current sub screen input finction.
SSIS01 INPUT1(SUB) ○ ○ Switches the sub screen to INPUT1.
SSIS02 INPUT2(SUB) ○ ○ Switches the sub screen to INPUT2.
SSIS03 INPUT3(SUB) ○ ○ Switches the sub screen to INPUT3.
SSIS04 INPUT4(SUB) ○ ○ Switches the sub screen to INPUT4.
SSIS05 INPUT5(SUB) ○ ○ Switches the sub screen to INPUT5.
STD STANDARD W/B ○ Returns the integrator PICTURE and WHITE BALACE to the factory
settings.
SVL SUB VOLUME: *** ○ ○ Adjusts the sub volume.
SZM ######## ● ● Displays the current screen size setting.
SZMS00 PIX by PIX or PARTIAL ○ ○ Sets the scree size to PIX by PIX or PARTIAL.
SZMS01 STD (4:3) ○ ○ Sets the screen size to Standard 4:3.
SZMS02 ANAMPHC 16:9 ○ ○ Sets the screen size to Anamorphic 16:9
SZMS03 LETTERBOX ○ ○ Sets the screen size to LETTERBOX.
SZMS04 CINEMA ○ ○ Sets the screen size to CINEMA.
SZMS05 VIRTUALWIDE ○ ○ Sets the screen size to VIRTUALWIDE.
SZMS08 FULL1035i ○ ○ Sets the screen size to FULL1035i.
SZMS09 UNDERSCAN ○ Sets the screen size to UNDERSCAN.
T TNT TINT: *** ○ ○ Adjusts the TINT.