RIDGID BS14002 - Manual (Page 25)

25
WARNING:
Do not allow familiarity with tools to make you
careless. Remember that a careless fraction of a
second is sufficient to inflict severe injury.
WARNING:
Always wear safety goggles or safety glasses with
side shields during power tool operation or when
blowing dust. If operation is dusty, also wear a
dust mask.
WARNING:
To avoid blade contact, adjust the blade guide
assembly to just clear the workpiece. Failure to
do so could result in serious personal injury.
APPLICATIONS
You may use this tool for the purposes listed below:
n
Scroll cutting and circle cutting of wood and wood com-
position products
n Relief cutting of wood and wood composition products
BASIC OPERATION OF THE BAND SAW
A band saw is basically a “curve cutting” machine that can
also be used for straight-line cutting operations like cross
cutting, ripping, mitering, beveling, compound cutting, and
resawing. It is not capable of making inside or non-through
cuts.
This band saw is designed to cut wood and wood
composition products only.
Before starting a cut, watch the saw run. If you experience
excessive vibration or unusual noise, stop immediately. Turn
the saw off, remove the switch key, and unplug the saw. Do
not restart until locating and correcting the problem.
CUTTING PROCEDURES
n Hold the workpiece firmly against the saw table.
n Use gentle pressure and both hands when feeding the
work into the blade. Do not force the work; allow the
blade to cut.
n The smallest diameter circle that can be cut is determined
by blade width. A 1/4 in. (6 mm) wide blade will cut a
minimum diameter of 1-1/2 in. (38 mm); a 1/8 in. (3 mm)
wide blade will cut a minimum diameter of 1/2 in. (13
mm).
n Keep your hands away from the blade. Do not hand
hold pieces so small your fingers will go under the blade
guard.
OPERATION
n Avoid awkward operations and hand positions where a
sudden slip could cause serious injury from contact with
the blade. Never place hands in blade path.
n Use extra supports (tables, saw horses, blocks, etc.) when
cutting large, small or awkward workpieces.
n Never use a person as a substitute for a table extension
or as additional support for a workpiece that is longer or
wider than the basic saw table.
n When cutting irregularly shaped workpieces, plan your
work so it will not pinch the blade. For example, a piece
of molding must lay flat on the saw table. Workpieces
must not twist, rock or slip while being cut.
When backing up the workpiece, the blade may bind in
the kerf (cut). This is usually caused by sawdust clogging
the kerf or when the blade comes out of the guides. If this
happens:
n
Wait until the saw has come to a full and complete
stop.
n Place the switch in the OFF (O) position then remove the
switch key from the switch assembly. Store key in a safe
place.
n Unplug the saw from the power source.
n Wedge the kerf open with a flat screwdriver or wooden
wedge.
n Open front cover and turn the upper wheel by hand while
backing up the workpiece.
RELIEF CUTS
Relief cuts are made when an intricate curve (too small a
radius for the blade) is to be cut. Cut through a scrap section
of the workpiece to curve in pattern line then carefully back
the blade out. Several relief cuts should be made for intricate
curves before following the pattern line as sections are cutoff
of curve “relieving” blade pressure.
SCROLL CUTTING
For general type scroll cutting, follow the pattern lines by
pushing and turning the workpiece at the same time. Do not
try to turn the workpiece while engaged in the blade without
pushing it – the workpiece could bind or twist the blade.
REMOVING JAMMED MATERIAL
Never remove jammed cutoff pieces until the blade has come
to a full and complete stop.
n
Place the switch in the OFF (O) position, remove the
switch key from the switch assembly.
n Unplug the saw from the power source before removing
jammed material.