Radio Shack DVD / VCR - Manual (Page 27)

2 2
3 3
4 4
7 7
5 5
6 6
– 27 – EN
Quick Use Guide
✄
Please refer to “Basic TV
Connection” on the front page
before you use this unit.
RF Output Channel
If channel 3 is already occupied for
broadcasting,
1)Set your TV to channel 4.
2)Insert a pre-recorded tape into this
unit.
3)Press [OUTPUT] on the unit so that
the VCR OUTPUT light is lit.
• If noise appears on the TV screen,
press [VCR/TV] on the remote control.
4)Press [PLAY B] once.
5)After a few seconds, hold [PLAY B]
on the unit for 3 seconds.
• The RF output channel will change
to channel 4 from channel 3 and you
will see a playback picture.
• When a picture does not appear on
the TV screen, repeat step 4).
6)Press [STOP C] to stop playback.
Connections 1
Clock Setup 5
VCR/DVD Switching
3
Installing the Batteries
for the Remote Control 2
Turn on the unit for the
first time 4
2 3 1
VCR DVD OUTPUT
POWER
DISPLAY VCR DVD PAUSE
SLOW
VCR/TV
SKIP/CH.
PLAY
STOP
REC/OTR
MENU
SETUP TOP MENU
MODE ZOOM
SUBTITLE T-SET ANGLE
ENTER
RETURN
SEARCH MODE
REPEAT A-B
OPEN/CLOSE /EJECT SPEED AUDIO
CLEAR/ C. RESET
1 2 3
4 5 6
7 8 9
0 +10
OUTPUT button
DVD OUTPUT light
VCR OUTPUT light
DVD button
VCR button
POWER OPEN/CLOSE
VCR DVD CHANNEL OUTPUT VIDEO L - AUDIO - R
STOP/EJECT PLAY STOP PLAY
REC/OTR E REW P / A
A
L K O F.FWD D P O
Press [VCR] on the remote control.
(Verify that the VCR OUTPUT light is lit.)
VCR MODE
Press [DVD] on the remote control.
(Verify that the DVD OUTPUT light is lit.)
DVD MODE
2 2
LANGUAGE SELECT
B ENGLISH [ON]
FRANCAIS
ESPAÑOL
1 1
Turn on the TV and set it
to channel 3.
• If channel 3 is already occupied for broadcasting,
see“RF Output Channel” section.
3 3
CH 01
AUTO SET UP
No No Please wait for a few minutes.
After scanning...
• The tuner stops on the lowest memorized
channel.
• You can select only the channels memo-
rized in this unit by using
[SKIP/CH. G G /K K H/L L ]
(or [CHANNEL K K /L L ]).
• If “AUTO SET UP” appears on the TV
screen again, check the cable connections.
Then, press [B] once again.
Y Y es es Press [MENU]
to exit.
Do you connect the cable from the cable box or
the satellite box to the unit’s ANT-IN jack?
YES
NO
TV Screen Remote Control
VCR VCR VCR
VCR VCR
1 1
- M E N U -
TIMER PROGRAMMING
AUTO REPEAT [OFF]
CHANNEL SET UP
B CLOCK SET
LANGUAGE SELECT
AUDIO OUT
TV STEREO
[ON]
SAP
CLOCK SET
MONTH DAY YEAR
1 0 / – – – – – –
HOUR MINUTE AM/PM
– – : – – – –
CLOCK SET
MONTH DAY YEAR
1 0 / 0 2 – – – –
HOUR MINUTE AM/PM
– – : – – – –
Select the current month.
Select the current day.
• If the clock is not set, the
CLOCK SET screen
appears when you press
[MENU]. In this case, go
to step 2).
VCR VCR VCR
VCR VCR
CLOCK SET
MONTH DAY YEAR
1 0 / 0 2 2 0 0 6
HOUR MINUTE AM/PM
– – : – – – –
CLOCK SET
MONTH DAY YEAR
1 0 / 0 2 MON 2 0 0 6
HOUR MINUTE AM/PM
0 5 : – – – –
CLOCK SET
MONTH DAY YEAR
1 0 / 0 2 MON 2 0 0 6
HOUR MINUTE AM/PM
0 5 : 4 0 – –
CLOCK SET
MONTH DAY YEAR
1 0 / 0 2 MON 2 0 0 6
HOUR MINUTE AM/PM
0 5 : 4 0 P M AM
B PM
Select the current year.
Select “AM” or “PM”.
8 8 To exit the CLOCK SET
screen
Select the current hour.
Select the current minute.
Hint Hint
• Pressing only [OUTPUT] on the front
panel DOES NOT switch the mode of the
remote control. You MUST select the cor-
rect mode on the remote control.
or
POWER
MENU
or
or
or
or
or
or
or