Radio Shack PRO-93 - Manual (Page 49)

49 Special Features
that operate are FUNC , / , SQUELCH , and VOL-
UME .
Note: You cannot activate the key lock while you are en-
tering a frequency into a channel.
To turn on the key lock, press FUNC then / . '<P '<P '<P '<P
CF:B<;ô CF:B<;ô CF:B<;ô CF:B<;ô appears for about 1 second. '<Pý CF:B<;ô '<Pý CF:B<;ô '<Pý CF:B<;ô '<Pý CF:B<;ô ap-
pears when you press any key after locking the keypad.
To turn off the key lock, press FUNC then / . The
scanner beeps three times and '<PýLECF:B<; '<PýLECF:B<; '<PýLECF:B<; '<PýLECF:B<; appears.
CHANGING THE DISPLAY CONTRAST
1. Press MANUAL .
2. Press FUNC then 9 . 1J<ý 1Gó FNEý B<PJý KFý J<K 1J<ý 1Gó FNEý B<PJý KFý J<K 1J<ý 1Gó FNEý B<PJý KFý J<K 1J<ý 1Gó FNEý B<PJý KFý J<K
:FEKI8JKô :FEKI8JKô :FEKI8JKô :FEKI8JKô appears.
3. Press
8 8 8 8
or
9 9 9 9
to select the contrast.
4. Press ENTER to set the display contrast.
CLONING THE PROGRAMMED DATA
You can transfer the programmed data to and from an-
other RadioShack Pro-93 or a Pro-2053 scanner using
an optional connecting cable with
1 /
8
-inch phone plugs
on both ends, (not included) available at your local Ra-
dioShack store.
Follow these steps to clone the data.
1. Turn on both scanners.
2. Connect the connecting cable to each scanner's PC/
IF jack. чб( чб( чб( чб(+*!э)+ ! +*!э)+ ! +*!э)+ ! +*!э)+ !чэ1 чэ1 чэ1 чэ1,ýKFýJ<E;õýI<DFM<ý:89C<ýKF ,ýKFýJ<E;õýI<DFM<ý:89C<ýKF ,ýKFýJ<E;õýI<DFM<ý:89C<ýKF ,ýKFýJ<E;õýI<DFM<ý:89C<ýKF
<O@ <O@ <O@ <O@Kô Kô Kô Kф
ээээ
appears.
3. Press
8 8 8 8
. áFE=@IDýJ<E;ý;8K8еэсж5 бFE=@IDýJ<E;ý;8K8еэсж5 бFE=@IDýJ<E;ý;8K8еэсж5 бFE=@IDýJ<E;ý;8K8еэсж5!/э, !/э, !/э, !/э,I<JJýFK?<I I<JJýFK?<I I<JJýFK?<I I<JJýFK?<I
B<Pý=FIý* B<Pý=FIý* B<Pý=FIý* B<Pý=FIэ*+ф +ф +ф +фээээ appears.
4. Press 1 to send the data to the other unit or press
any other key to cancel the operation.