Radio Shack PRO-2053 - Manual (Page 33)

33 Trunking Operation
Follow these steps to program Motorola
trunking frequencies in the UHF-Lo band:
1. Press PROG then TRUNK to enter the ID
program mode.
2. Press FUNC and press (or hold)
8 8 8 8
or
9 9 9 9
to select the bank.
3. Press MODE and select )+0 )+0 )+0 )+0 .
4. Press FUNC then 2 . The display indi-
cates â8J<ý =I<Hôèý â8J<ý =I<Hôèý â8J<ý =I<Hôèý â8J<ý =I<Hôèý on the first line,
о о о отмф тмф тмф тмфтттт тттт тттт тттт on the second line,
E\\i[jэ0э).& E\\i[jэ0э).& E\\i[jэ0э).& E\\i[jэ0э).&
on the third line and /K<Gэ иэ ðíôòB$Q /K<Gэ иэ ðíôòB$Q /K<Gэ иэ ðíôòB$Q /K<Gэ иэ ðíôòB$Q on
the bottom line.
5. While в в в в in â8J< â8J< â8J< â8J< blinks, if necessary,
press the desired base frequency with
the number keys and press
ENTER .
Confirm the entry. If it is incorrect, press
the number keys again to set the base
frequency. After you confirm the input,
press
ENTER again.
6. While
Eý Eý Eý Eý
in
E\\i[j E\\i[j E\\i[j E\\i[j
blinks, if necessary,
enter the offset number and press
ENTER . Confirm the entry. If it is incor-
rect, then press the number keys again
to set the frequency. After you confirm
the input, press
ENTER again.
7. While / / / / in /K<G /K<G /K<G /K<G blinks, repeatedly press
8 8 8 8
or
9 9 9 9
to select the step number,
рнфт рнфт рнфт рнфт , нтфт нтфт нтфт нтфт or срфнэ B$Qх срфнэ B$Qх срфнэ B$Qх срфнэ B$Qõ then press
ENTER .
8. Press PROG to enter the program mode.
9. Store the trunking IDs into the sub-bank
in the same bank.
Programming Motorola Trunking
System (800 MHz)
On the 800 MHz trunking band, you can se-
lect a base frequency (normal or offset).
On the 900 MHz trunking band, you do not
need to set the base/offset/step frequency.
Follow these steps to program 800 MHz
band Motorola trunking.
1. Press PROG then TRUNK to enter the ID
program mode.
2. Press FUNC then
8 8 8 8
or
9 9 9 9
to select the
desired bank.
3. Press MODE and select Motorola trunk-
ing mode.
4. Press FUNC then 3 .
5. Press
8 8 8 8
or
9 9 9 9
to select *FID8C *FID8C *FID8C *FID8C or +== +== +== +== -
J<K J<K J<K J<K and press ENTER .
Notes:
• The default setting is *FID8C *FID8C *FID8C *FID8C . If you can
not receive with the *FID8C *FID8C *FID8C *FID8C setting,
change to +==J<K +==J<K +==J<K +==J<K .
• The base frequency in *FID8C *FID8C *FID8C *FID8C is
851.0125 MHz. The base frequency in
+==J<K +==J<K +==J<K +==J<K is 851.0000 MHz.
Programming Fleet Maps
You must set the fleet map if you want to re-
ceive a Motorola Type I system. Fleet maps
are included along with other information
about Motorola Type I systems at
www.trunkscanner.com.
Follow these steps to program a fleet map.
1. Press PROG then TRUNK .