Radio Shack PRO-2053 - Manual (Page 37)

37 Trunking Operation
Locking Out Talk Group IDs
Note: You can only lock out talk group IDs
when the scanner is in the closed mode (see
“Open and Closed Modes” on Page 38).
1. Press PROG .
2. Press TRUNK .
3. Press FUNC ,
8 8 8 8
or
9 9 9 9
to move to the
desired bank.
4. Press
8 8 8 8
or
9 9 9 9
to select the ID memory.
5. Press L/OUT to lock out the ID.
BBBB
appears.
6. To remove the lockout from a trunking
ID, manually select the ID memory, and
press
L/OUT until ( ( ( (
ээээ
disappears.
While the scanner shows a text tag you can
confirm the ID code when the received signal
is the voice channel.
1. Press TEXT while the scanner is receiv-
ing the voice channel and displaying the
text tag. The ID code appears as
)+0и444444 )+0и444444 )+0и444444 )+0и444444
or
! и4444 ! и4444 ! и4444 ! и4444 .
2. Press TEXT again to cancel.
Delay Function in ID Indication
Mode
You can set the ID delay function separately
from channel delay.
1. Press FUNC then ./DELAY while you are
programming the trunked ID. 1J<ý 1Gó 1J<ý 1Gó 1J<ý 1Gó 1J<ý 1Gó
FNEýB<PJýKFýJ<Kэ% э;<C8P FNEýB<PJýKFýJ<Kэ% э;<C8P FNEýB<PJýKFýJ<Kэ% э;<C8P FNEýB<PJýKFýJ<Kэ% э;<C8P
.
ýýýýðôòýJ<:FE;J ðôòýJ<:FE;J ðôòýJ<:FE;J ðôòýJ<:FE;J
appears.
2. Press
8 8 8 8
or
9 9 9 9
to select *FE< *FE< *FE< *FE< , тфн тфн тфн тфн , сфт сфт сфт сфт , сфн сфн сфн сфн ,
рфт рфт рфт рфт , рфн рфн рфн рфн , пфт пфт пфт пфт , пфн пфн пфн пфн or офт офт офт офт J<:FE;J J<:FE;J J<:FE;J J<:FE;J .
3. Press ENTER .
If the ID delay is active, it watches the control
channel command for the delay time when-
ever the signal disappears from the voice
channel.
Reviewing Locked-Out Talk Group
IDs
Note: You cannot clear all lockouts from a
talk group at the same time.
1. Press PROG then TRUNK .
2. Press FUNC then L/OUT . The locked out
ID appears. If the ID memory bank has
no locked out ID, you hear the low beep
tone.
3. Press FUNC then
8 8 8 8
or
9 9 9 9
to select a
search bank. Or, just press
8 8 8 8
or
9 9 9 9
to
search for any locked out IDs in a bank.
Clearing Talk Group IDs
1. Press PROG then TRUNK .
2. Press FUNC ,
8 8 8 8
or
9 9 9 9
to select ID
memory.
3. Press FUNC then CLEAR .
Clearing All Talk Group IDs in One
Bank
You can clear all talk group IDs within a
bank. This lets you quickly delete all talk
group IDs from a bank if you want to use the
bank to store different data (such as a new
set of talk group IDs).
1. Press PROG .
2. Press TRUNK to enter a talk group ID
memory mode.
3. Select a talk group ID bank using FUNC ,
8 8 8 8
or
9 9 9 9
.