Omron BF306 - Manual (Page 4)

References: Deurenberg* P
, Y
ap M, van Staveren W
A
.
Body mass index and percent body fat: a meta-analysis among different ethnic groups. International Journal of Obesity 1998;22:1164-1171 WHO Obesity: Preventing and managing the global epidemic. Report on a WHO Consultation on Obesity
, Geneva, 3-5
June, 1997 WHO/NUT/NCD/98.1, Geneva 1998 * Paul Deurenberg, PhD Associate Professor in Nutrition, W
ageningen University
,
The Netherlands V
isiting Professor University 'T
or V
ergata', Rome, Italy
Nutrition Consultant in Singapore 5.
TROUBLESHOOTING
5.1 Possible causes of inaccurate measurements. Measuring postures that should be avoided Measurement in the following positions may not provide accurate measurement. How to hold the grips. In the following cases, the electric resistance may not be measured correctly
.
5.2 Explanation of error codes Error display
Cause
What to do (the next button to push)
Electrodes were not
Grasp the grips cor
-
firmly grasped.
rectly and measure. (Start button)
Measurement posture
M
e
a
s
ure without or
grip was not stable.
moving your arms. (Start button)
Hands are dry
.
Slightly moisten hands with a wet towel, then measure. (Start button)
The values of body
Check the set height,
fat percentage and
weight, age, and
BMI are outside the
gender again. (Set
measurable range.
button)
Abnormal operation
Press the O/I button again and start measurement. If this error occurs again, consult the nearest Omron dealer
.
5.3 T
roubleshooting
T
rouble
What to inspect
How to repair
When the O/I
Are the batteries
Replace both
button is
worn out?
batteries with
pushed,
nothing
n
e
w
5
o
n
e
s
is displayed.
Is the battery
Insert the batteries
polarity correct?
correctly
.
The value of body
Is the measurement
M
easure again in
fat percentage
posture correct?
correct posture.
displayed is ab- normally high (or low). An error (E1 to E6)
P
le
ase refer to "Explanation of Error
is displayed and
Codes". (see above)
the measurement is impossible. The results differ
Please refer to "How to Obtain a Correct
extremely for each
M
easurement"
measurement. Other conditions.
Push the O/I button again and restart from the beginning
If you are unable to obtain a correct measurement after taking the above-mentioned troubleshooting steps, please contact the nearest OMRON dealer
.
English
7
Elbows are bent. Arms held at an angle, either too low ot too high.
Measuring while lying down or sitting. Moving your body or arms during measurement.
Y
our fingers are
not properly gripping the electrodes.
When holding the grips, the hands are positioned unevenly towards the top or the bottom.
3.5 Setting and using personal memory number The Omron BF 306 body fat monitor has a memory function. This function enables you to store the data for 9 persons. Push the O/ I button All the display segments turn on When you want to set the personal memory number and store personal data: Select the personal memory number
.
1. Push
the
▼
/▲
button and select a
personal number from 1 to 9.
2. Push the Set button. The personal number turns on and changes to height setting mode. 3.
Set the personal data - continue with step 3 paragraph 3.3 "Setting personal data".
T
aking a measurement by using your personal memory (be
sure the device is on): Search your personal memory number 1. Push
the
▼
/▲
button to select your memory number
2. Push the Set button. The memory number is indicated and your personal data is displayed. 3. Carry out the measurement. Refer to "T
o take the measurement” paragraph 3.4
3.6 T
o
change any values
1.
Push the Set button to go to the personal data you want to change.
2. Push the
▼
/▲
button to change the setting.
By pushing both the
▼
/▲
buttons at the same time, the
current flashing display will reset to the initial value. How to delete all 9 personal data values from the memory 1. Push the
▲
button and select the memory No. 1.
2. Push the SET button for 2 seconds. 3. All personal data is deleted and all. 4.
The display segments turn on.
(Same state as when the O/I button is pushed.) If you leave the set items on the screen without confirma- tion, in approximately 1 minute the display will change to the initial values or the to values before setting. After 1 minute, the unit will automatically turn off. If your age, weight, or height has changed, correct the value accordingly
.
4.
HOW TO INTERPRET MEASURED RESUL
TS
4.1 BMI V
a
lue
BMI is an internationally used index to show the body condition by checking the balance between the height and the weight. It is calculated by the following formula: BMI = weight / height
2
BMI
B
MI value*
< 18.5
LOW
>18.5 and < 25
NORMAL
> 25 and < 30
HIGH
> 30
TOO HIGH
*
The above mentioned indices refer to the values for obesity proposed by the WHO (W
orld Health Organization)
4.2 Body fat percentage Displays the body fat mass as the percentage of body weight. Obesity judgment
Low
Normal
High
T
oo high
English
6
BODY FAT MONITOR BF306 BODY FAT MONITOR BF306
0 %
10
%
20
%
30
%
40
%
50
%
30 – 39 18 – 29 age
bodyfat%
40 – 49 50 – 59 60 – 70 Female
0 %
10
%
20
%
30
%
40
%
50
%
30 – 39 18 – 29 age
bodyfat%
40 – 49 50 – 59 60 – 70 Male
Graphical inter- pretation of BMI value (LOW >> TOO HIGH) Graphical inter- pretation of measured F
A
T%,
based on Deurenberg’
s*
table below