Sylvania DVR91DG - Manual (Page 8)

8 EN
Functional overview
Before you start
Front Panel
1. Disc tray
Place a disc when open.
2. Display
Refer to “Front Panel Display Guide” on page 12.
3. OPEN/CLOSE A button*
Press to open or close the disc tray.
4. CHANNEL L / K button
Press to change the channel up and down.
5. REV E button
During playback, press to skip to the previous chapter
or track.
During playback, press and hold for 1.5 seconds to
fast reverse.
When playback is paused, press to play reverse step
by step.
When playback is paused, press and hold for 1.5 sec-
onds to slow reverse.
6. FWD D button
During playback, press to skip to the next chapter or track.
During playback, press and hold for 1.5 seconds to
fast forward.
When playback is paused, press to play forward step
by step.
When playback is paused, press and hold for 1.5 sec-
onds to slow forward.
7. STOP C button
Press to stop play or recording.
8. PLAY B button*
Press to start or resume play.
9. POWER button
Press to turn the unit on and off.
If timer programmings have been set, press to set the
unit in timer-standby mode.
10. AUDIO input jacks (LINE2)
Use to connect external equipment with standard
audio cable.
11. VIDEO input jack (LINE2)
Use to connect external equipment with a standard
video cable.
12. S-VIDEO input jack (LINE2)
Use to connect the S-Video output of external equip-
ment with an S-Video cable.
13. REC/OTR button
Press once to start a recording. Press repeatedly to
start a One-touch Timer Recording.
14. REC SPEED button
Press to switch the recording speed.
15. Remote control sensor
Receive signals from your remote control so that you
can control the unit from a distance.
Rear Panel
ANTENNA AUDIO IN
VIDEO IN
L
R
AUDIO OUT
VIDEO OUT
(L1)
IN
IN
OUT
OUT
S-VIDEO
COMPONENT
VIDEO OUTPUT
L
Y
P B /C B
P R /C R
R
DIGITAL AUDIO OUTPUT
PCM / BITSTREAM
COAXIAL
1 2 3 4
5 6 7 8 9 10 11
1. ANTENNA IN jack
Use to connect an antenna.
2. VIDEO IN jack (LINE1)
Use to connect external equipment with a standard
video cable.
3. VIDEO OUT jack
Use to connect a TV monitor, AV receiver or other
equipment with a standard video cable.
4. AC Power Cord
Connect to a standard AC outlet to supply power to
this unit.
5. COAXIAL DIGITAL AUDIO OUTPUT jack
Use to connect an AV receiver, Dolby Digital decoder
or other equipment with a coaxial digital input jack
with a digital coaxial cable.
6. AUDIO OUT jacks
Use to connect a TV monitor, AV receiver or other
equipment with standard audio cable.
7. COMPONENT VIDEO OUTPUT jacks
Use to connect a TV monitor with component video
inputs with component video cables.
8. S-VIDEO OUT jack
Use to connect the S-Video input of a TV monitor,
AV receiver or other equipment with an S-Video
cable.
9. S-VIDEO IN jack (LINE1)
Use to connect the S-Video output of external equip-
ment with an S-Video cable.
10. AUDIO IN jacks (LINE1)
Use to connect external equipment with standard
audio cable.
11. ANTENNA OUT jack
Use to connect an antenna cable to pass the signal
from the TV ANTENNA IN to your TV monitor.
Note
• Do not touch the inner pins of the jacks on the rear panel. Electrostatic discharge may cause permanent
damage to the unit.
• This unit does not have the RF modulator.
REC/OTR REC SPEED
OPEN/CLOSE CHANNEL REV FWD STOP PLAY POWER
S-VIDEO VIDEO AUDIO L R
8*9
1211 10 13 14 15
1 2 3* 4 5 6 7
(*) The unit can also
be turned on by
pressing these
buttons.
DVR91DG_E7A01UD.indd 8 2006/02/15 17:25:57